Well, another delivery attempt was made today, woke up to relieve some pressure, went up stairs expecting to find Erli on me door step. Since I left a signed hanger on my main door. Opened the door to find another fracking door hanger, sorry we missed you. To say I was livid, would be way under stated.
Called the frakers cell
and lit into him. he goes but, but, did you leave it on the same door I hung mine on?? NO, I put it on the door you could easily see from your fraking truck, without getting out. grr,
At this point, once off the phone, was so fraking loosing it, hulk like, seek destroy, kill, kind of thing
that I couldn't get back to sleep. Sooo, went online to DHL wed site to log a complaint, the live chat popped up, just before was going to send me message, asking if assistance was needed, well, copied and pasted me final edit of my big beeche and, after saying, no I don't want to file a complaint against the driver, just want me package. she promised delivery the next day.
Couple hours later, after my morning shower, and while making coffee, went to go check the vapebox, noticed my hand written note & the door hanger authorization was missing, went to the side door, and there she was, Erli Was Home.!!!
Threw on a 0.4 ohm coil, ramie fiber wick, stipped wick in half, trimmed off the top part, tirmming the tail in the channel and 1-2 mm from the bottom
Damn, sorry about the delay, hang on,
Damn, that's a good vape
any who, just finished my first tank load, and had to refill this thirsty girl. Received the 23mm 9ml tank, along with the crown ss drip tip and adaptor, so at work, went through at least 7 ml, and I also had 2 other mods with flashi V2's on them. Erli wasn't the only vape being used. Although I did drain a VTC4 down to 3.2 volts, lower than I like. woops
K, must say, the Erlkonigin is one fine rba. Probably one of the smoothest draws out there, oh, by the way, I am not using that silly ac thingy, find that when builds are 0.4 ohms and lower, ac is the last thing needed, have removed all ac rings and or screws from all me rba's. just not needed. Think my major beatch abour Erli, is the lack of post hole's. I've been using 22 gage Kanthal lately, and trappin under screw heads can prove problematic. and the space between the positive screw head and side wall are so close, had to wrap around counter clock wise, to avoid shorting.
Though do like the fill holes, find filling the SS tanks easier to unscrew the top cap, fill her up, fasten the tank top cap, since there's 2 air holes, there is no danger of pressure flooding the build, like a kafun would,
had to laugh at P.B's comment about being surprised it didn't flood upon filling,
, common, really? lmao
After finger tightening then tighten with the top cap, good to go, no flood gurgle, nota.
This is one fine rba, is it perfect??? almost, but not, but then again, everyone's vape is different. Once Max gets back with his upgrades, will see how Erli likes 90 watts, sure she'll handle 75 no prob. I simply love that she can hold 9 ml's of juice on board with out having to do an extension. Can easily see her always by my side.
Feel she is a fantastic addition to any collection, glad she's here. For my first wicking, have it almost where it needs to be, think a few strands of fiber have to be removed in the wick channels though, but will give it another day for the cell walls to firm up before modifying. Right now it vapes almost as good as my flashi's do. Have them all with the exact same build all within 0.02 ohm's of each other. But then have been building the flashi since before Christmas.
any who, a worthy contender, and a must have for tank lovers. Will definitely keep an eye on this designer. Good chit, but then you all know that, just takes a bit longer for Phil.
