The newest RDA by UD (maker of the IGO-W) Come check out the IGO-M!!!!!!! Just released this week!!!!

[Ray Lopez]

IGO-M Rebuildable Drip Atomizer rda

• Designed by Magbay Distributor
• Adjustable Airflow
• Manufactured by Youde Technology
• Stainless Steel Construction
• Height - 32mm
• Diameter - 22mm
• Spare parts bag (includes wick/wire & wrench)
  
  I just saw this today and DAMN this looks slick!!! Possibly one the best rda's to come out of this company.
  I've only seen one site doing pre-sales on these right now: IGO-M
  
  I'm getting one for sure!
  
  What do you guys think????

 

[SonHouse]

Looks interesting but it better do tricks if they expect me to pay $40 plus shipping for it...

 

[emus]

Looks like a good cloud chaser.

 

[Bosco]

I like the way the deck looks. I don't think I've seen that particular design before with the center block. The airflow looks awesome, too. Just from the looks of it, I'd give it a go at $40 . .but probably we will actually pay a little less once multiple resellers start getting them. I'd have to say from the looks of it this will end up in my atty box . .can't wait for reviews and feedback about it.

 

[numbskull]

That top cap looks hideous IMO, but that deck reminds me of the Helios which I like.
Might get one.....
I'll probably get one.....
I'm getting one....

 

[Cuando]

I have had nothing but luck with the Youde RDA's, this one is going on the 'must have' list. Very nice, love the airflow control.

 

[spawnsharks]

Yep. Youde is a pretty solid build at a decent pricepoint. This is a little pricey for their line, but it will come down.

 

[Ray Lopez]

from what I was told is this is the very first run and only 500 have been made.

 

[jmsgolo]

This is a limited run item, there are only 500 at present time available. I am unsure if there will be another run of these.

 

[Jjshbetz11]

Deck looks great however, that cap looks quite big flavor wise. Someone needs to make a small cap big air holes dripper.

 

[suspectK]

I don't know why they put that huge slot in the deck.. They should figure out another way for airflow control, so people like me can flood the deck. It looks like you'll have about 1mm of area to fill, before it starts spilling out..that is with it straight up at all times too. I'm not too keen on just saturating a wick, taking 1-2 pulls, and saturating the wick again, all because I'm laying down, nor do I like the idea of keeping it straight up 100% of the time I'm using it.

 

[the4thpower3]

Yeah looks like a $40 leaker. Not enough deck lip/resevoir.

 

[Ray Lopez]

Not anything different from a igo-w drip well. If they placed it higher you'll have the wick and coil too high. I like my coil right in line with the air hole.

 

[wolfparty]

I tend to be on the generous side when it comes to dripping and am not a huge fan of leaking airholes. Maybe if they opted for trapping the wire underneath a traditional set of screws (as opposed to having holes in the posts), the airholes could have moved up a few mm's allowing for a deeper well.

 

[bender817]

I don't really like it. My buddy has the IGO-W3 and not only does it leak out of the slot in the reservoir, but it makes the airflow low and awkward. I like my IGO-W but I really think this thing just needs to be rethought. Maybe a deep well and raise the AFC up about 2mm or make something with an AFC ring on the cap.

 

[jmsgolo]

So far no problems with leaking, but I don't overdrip

 

[cantstopwontstop]

I will not stop till I have the whole IGO alphabet mwhahah! no seriously know of anywhere that's taking preorders??

 

[jmsgolo]

I will not stop till I have the whole IGO alphabet mwhahah! no seriously know of anywhere that's taking preorders??

Look at the first post, the link is at the bottom. Pre-orders will be shipped 1/29. Maybe sooner from what I hear

 

[Ohms Lawbreaker]

Too much like Swiss cheese for me but I like my W just fine.

 

[jmsgolo]

A tad hard to open and close the air flow with an igo w.