-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
The Overlooked Tootle Puffer Gear Thread
- Thread starter roxynoodle
- Start date
- th_trl_thread_readers 0
- Status
Boden didn't take the whole base apart on the k4 
Yeah, 21 parts are o rings. But, still, if you completely dismantle for cleaning, including all the o rings and seals, it is a pain.
Yeah, 21 parts are o rings. But, still, if you completely dismantle for cleaning, including all the o rings and seals, it is a pain.
Boden didn't take the whole base apart on the k4
Yeah, 21 parts are o rings. But, still, if you completely dismantle for cleaning, including all the o rings and seals, it is a pain.
And if you had a leak, can you imagine trying to figure out which o-ring was bad?
And if you had a leak, can you imagine trying to figure out which o-ring was bad?
On my first one, 3/4 of them were the wrong sizes! And the whole thing was caked in some horrible tar like substance
I had to break it all down to boil it, and replace every o ring and seal.
Here it is...I tried to search for that on FT and got a bunch of bug paraphernalia.
https://www.fasttech.com/products/0/10017701/3628800-gem-styled-rta-rebuildable-tank-atomizer
I couldn't tell Roxy posted the KF4 exploded diagram on my phone so I'll just remove mine...
Last edited:
I DON'T like a super airy draw. I MTL vape only. The one time I tried a lung hit, I thought I was going to lose a lung.
ETA: Andria, I would bet that Boden has the 4S kit installed on that kayfun. It gives it a much bigger airhole.
Hmm, I dunno, he's sort of a tootler.
I just eyeballed my Achilles' airhole... I'd estimate it at somewhere between 1.2-1.5mm; Frog in Fog's page says it's 2mm, but that appears to be the *outer* diameter, not the inner, OR, maybe they're referring to the small hole on the side, which might be 2mm -- that inner one under the coil is nowhere near that large! To me, this atty has PERFECT airflow -- it's like a carto, or like those evil old friends of ours, which are the things I'm trying to simulate the experience of.
I craved that particular oral sensation/activity when I tried the patch, and there's only so many milkshakes you can consume before they have to roll you everywhere you go. Andria
It is usually only one or two that cause problems.And if you had a leak, can you imagine trying to figure out which o-ring was bad?
In the short run. In the long run any or all have the possibility of degrading from dryness and age
Boden didn't take the whole base apart on the k4
Yeah, 21 parts are o rings. But, still, if you completely dismantle for cleaning, including all the o rings and seals, it is a pain.
Why would you break it down any further than I did for cleaning.
When I get a new tank I break it down, remove the o-rings place them on my parts grid (project mat) , wash the metal bits with everclear, wash the o-rings in soapy water, then rinse everything in distilled water.
Then I assenble acording to my parts grid.
Once in use I haven't done anything more than a quick rinse under the tap to any tank I've ever had.
In the short run. In the long run any or all have the possibility of degrading from dryness and age
Goodness!!! How many full rebuild kits do you have to keep all those tanks running in perpetuity?
I have four sets of spare parts for my Kayfun v4's
I would have sent it back. That's disgusting
It was a gift. I didn't want to put my friend out. There were just a ton of issues though, including parts that weren't tightened down, and the jc getting stuck.
I just have a giant batch of every size o ring I could possibly need so I don't buy rebuid kits. Same with screws.
A friend here in town asked me to prep a v4 that he got off fastech. I opened the clone Svoemesto box removed the clone poster and... OMG!!! It smelled like dead fish. It was covered in this wax like gunk that resembled old fry grease. I soaked it in gasoline for a day, took it out, rinsed it in turpentine, then windex, then water.
The spares kit was a joke.
All the o-rings were junk from the start so I made a needed parts list.
1. Complete rebuild kit
2. New chimney section (threads were too badly cut to use)
3. New jfc base (threads were seized)
I told him he could buy $40 worth of parts or stop buying crap clones from fastech...
A friend here in town asked me to prep a v4 that he got off fastech. I opened the clone Svoemesto box removed the clone poster and... OMG!!! It smelled like dead fish. It was covered in this wax like gunk that resembled old fry grease. I soaked it in gasoline for a day, took it out, rinsed it in turpentine, then windex, then water.
The spares kit was a joke.
All the o-rings were junk from the start so I made a needed parts list.
1. Complete rebuild kit
2. New chimney section (threads were too badly cut to use)
3. New jfc base (threads were seized)
I told him he could buy $40 worth of parts or stop buying crap clones from fastech...
Probably the same one as mine. I did get it working and clean though with maybe $2 worth of o rings.
- Status
Similar threads
