I use an Allan wrench the turn it makes is easier for me to line everything up at least on the manger heads
Sent from my iPhone using Tapatalk
The Provarinati Saloon
- Thread starter CrimsonJack
- Start date
- th_trl_thread_readers 0
- Status
I use an Allan wrench the turn it makes is easier for me to line everything up at least on the manger heads
Sent from my iPhone using Tapatalk
Currently they only carry two sizes, 2mm and 3mm.
On another note -woodville in the classies ....
So tempting! But my current grail is a red mini... A gal can dream, eh?
All you have to do is take a flat head screwdriver and turn the screw that is on the bottom of the Kayfun counterclockwise so that the screw sticks out farther than the housing it sits in. This should lower the connection point enough to make contact with the contact in the provari. If you have a clone that has the adjustable centerpin. If you do not, I can not help; I do not know what to tell you there.
You may have to try this a couple of times to figure out how far out the screw needs to be. You do not have to empty the juice out or anything. Should be a quick thing to try.
We should get together for lunch next we find ourselves in Purgatory together. Don't be shy. Shout out to me.
Last edited:
If it helps, I have found that putting the legs of the coil, in the bit/screwdriver/thingee........so that they sit inside the screws helps too. It is hard to explain in text but when the legs sit outside; it can move about but when they are inside. It gives some resistance on the other end while tightening one screw.
The delicate balance is not flying to Germany to punch the designer in the adam's apple
Awwee, c'mone .... make it a reality!!!!
I have been on the HUNT for one!! I wonder if ProVape has a dusty one lying around somewhere...
26 Gauge
Wire Type & Gauge: 26g Kanthal A-1
Coil size (what you wrap it on):1/16 drill bit
Number of Coils: 11
Measured Ohms of coil: ~.75ohm
26 ga. Kanthal A-1
8 wraps
14 ga. needle,
Ohms .9
wire: 26g Nichrome (= 25g Kanthal)
size (ID): 1/16" drill bit
# wraps: 8
resistance: 0.5Ω
wire/ 26g kanthal
coil size/ 16g blunt tip needle
wraps/ 8
Ω/ .6ish
Kanthal A1 26 awg
Wraped on .055" music wire
8 coils @ .7Ω
wire: 26 gauge Nichrome
size (ID): 1/16" Drill Bit
# wraps: 12
resistance: 0.9 ohms
26 AWG Nichrome 60
8/7 wraps touching
1/16 drill bit (micro coil)
0.5 Ω
26 AWG Nichrome 60
7/6 wraps touching
16 gauge blunt needle*
0.9Ω
26 ga. Kanthal A-1
8 wraps
14 ga. needle,
Ohms .9
27 Guage
wire: 27ga Kanthal A1
size (ID): 17ga blunt tip luer lock needle
# wraps: 14
resistance: 1.26 ohms
28 Gauge
Wire Type & Gauge: 28g Kanthal
Coil size (what you wrap it on):toothpick
Number of Coils:10
Measured Ohms of coil: 1.4
Wire Type & Gauge: 28g Kanthal
Coil size (what you wrap it on): 1/16 drill bit
Number of Coils:9
Measured Ohms of coil: 1.4
Wire Type & Gauge: 28g Kanthal A-1
Coil size (what you wrap it on): 2mm diameter screwdriver
Number of Coils: 9
Measured Ohms of coil: 1.2 ohm
Wire Type & Gauge: 28g Kanthal A-1
Coil size (what you wrap it on): 2mm diameter screwdriver
Number of Coils: 6
Measured Ohms of coil: .9 ohm
WIRE: 28g Kanthal
ID: 1/16"
WRAPS: 7/8 x 2
RES: 0.5Ω
. . . (1Ω/ea)
wire: 28g Kanthal A1
size (ID): 1/16" drill bit
# wraps: 12
resistance: 2.1Ω
28AWG Kanthol
5/64" machined cylinder (.0005 runout, overkill)
7.5 wraps
Wire: 28swg kanthal A1
Coil Bore: 1.5mm
Number of Coils: 5 + long tails
Ohms: 0.76
Wire Type & Gauge: 28g Kanthal A-1
Coil size (what you wrap it on):16 gauge needle
Number of Coils: 7/8
Measured Ohms of coil: ~1.0ohm
Wire Type & Gauge: 28g kanthal
Coil size (what you wrap it on): 1/16" drill bit
Number of Coils: 11
Measured Ohms of coil: 1.5 ohm
Kanthal A1 28 awg
1/16 drill bit
10 wraps
1.2Ω on rm2
28 ga
8 wraps
1/16" drill bit
1.0 ohm
Kanthal A1 28 awg
Wraped on .0625" (1/16") music wire
10 coils @ 1.2Ω
28 AWG Kanthal A1
5/4 wraps
1/16 drill bit
0.9Ω
29 Gauge
WIRE: 29g Kanthal
ID: 1.5mm (.0589")
WRAPS: 7/8 x 2
RES: 0.6Ω
. . . . (1.2Ω/ea)
30 Gauge
Kanthal A1 30 awg
Wraped on .0625" (1/16") music wire
12 coils @ 2.2Ω
Kanthal A1 30 awg
Wrapped on .047" music wire
16 coils 2.6Ω ea, total 1.3Ω
Kanthal A1 30 ga
~1/16 jeweler's screwdriver
11 wraps
1.82 ohms
Wire Type & Gauge: 30g Kanthal
Coil size (what you wrap it on): a heavy paperclip leg that's about equivalent to a 16g needle
Number of Coils: 10
Measured Ohms of coil: 1.8
Wire / 30 ga kanthal
coil / size "ID" 1.96 mm "screw driver"
Wraps 7
1.6 ohm
Wire Type & Gauge:30g Kanthol
Coil size (what you wrap it on):1/16 drill bit
Number of Coils:9
Measured Ohms of coil:1.6
Wire Type & Gauge: 30ga kanthal
Coil size (what you wrap it on): Doubled-over 3mm silica
Number of Coils: 4
Measured Ohms of coil: 1ohm
30 ga Kanthal
~1/16 screwdriver
11 wraps pulled really tight while wrapping
1.78 ohms
30 AWG Kanthal A1
13/14 wraps on 1/16 drill bit
Cotton wick
2.5Ω
Wire Type & Gauge: Kanthal 30g
Coil size (what you wrap it on): Supe's 17g needle (Thanks Supe!)
Number of Coils: 10
Measured Ohms of coil: 1.9
wire: 30ga Kanthal A1
size (ID): 16ga blunt tip luer lock needle
# wraps: 12
resistance: 2.3Ω
32 Gauge
Wire Type & Gauge: 32g Kanthal A-1
Coil size (what you wrap it on):Tiny screwdriver, roughly the size of a 16 gauge needle
Number of Coils: 17
Measured Ohms of coil: ~3.0ohm
Kanthal A1 32 awg twisted 2 stands
Wrapped on 1mm Ekowool with .039" (1mm) music wire core
8 coils, 1.1Ω
Wire Type & Gauge: 32g kanthal
Coil size (what you wrap it on): 1/16" drill bit
Number of Coils: 10
Measured Ohms of coil: 2.4 ohm
Wire Type & Gauge: 32g Kanthal
Coil size (what you wrap it on): my trusty paperclip leg
Number of Coils: 14 or 15?
Measured Ohms of coil: 3.8
Wire Type & Gauge: 32 gauge twisted
Coil size (what you wrap it on): round wooden toothpick
Number of Coils: 6
Measured Ohms of coil: 1.4
Wire Type & Gauge: 26g Kanthal A-1
Coil size (what you wrap it on):1/16 drill bit
Number of Coils: 11
Measured Ohms of coil: ~.75ohm
26 ga. Kanthal A-1
8 wraps
14 ga. needle,
Ohms .9
wire: 26g Nichrome (= 25g Kanthal)
size (ID): 1/16" drill bit
# wraps: 8
resistance: 0.5Ω
wire/ 26g kanthal
coil size/ 16g blunt tip needle
wraps/ 8
Ω/ .6ish
Kanthal A1 26 awg
Wraped on .055" music wire
8 coils @ .7Ω
wire: 26 gauge Nichrome
size (ID): 1/16" Drill Bit
# wraps: 12
resistance: 0.9 ohms
26 AWG Nichrome 60
8/7 wraps touching
1/16 drill bit (micro coil)
0.5 Ω
26 AWG Nichrome 60
7/6 wraps touching
16 gauge blunt needle*
0.9Ω
26 ga. Kanthal A-1
8 wraps
14 ga. needle,
Ohms .9
27 Guage
wire: 27ga Kanthal A1
size (ID): 17ga blunt tip luer lock needle
# wraps: 14
resistance: 1.26 ohms
28 Gauge
Wire Type & Gauge: 28g Kanthal
Coil size (what you wrap it on):toothpick
Number of Coils:10
Measured Ohms of coil: 1.4
Wire Type & Gauge: 28g Kanthal
Coil size (what you wrap it on): 1/16 drill bit
Number of Coils:9
Measured Ohms of coil: 1.4
Wire Type & Gauge: 28g Kanthal A-1
Coil size (what you wrap it on): 2mm diameter screwdriver
Number of Coils: 9
Measured Ohms of coil: 1.2 ohm
Wire Type & Gauge: 28g Kanthal A-1
Coil size (what you wrap it on): 2mm diameter screwdriver
Number of Coils: 6
Measured Ohms of coil: .9 ohm
WIRE: 28g Kanthal
ID: 1/16"
WRAPS: 7/8 x 2
RES: 0.5Ω
. . . (1Ω/ea)
wire: 28g Kanthal A1
size (ID): 1/16" drill bit
# wraps: 12
resistance: 2.1Ω
28AWG Kanthol
5/64" machined cylinder (.0005 runout, overkill)
7.5 wraps
Wire: 28swg kanthal A1
Coil Bore: 1.5mm
Number of Coils: 5 + long tails
Ohms: 0.76
Wire Type & Gauge: 28g Kanthal A-1
Coil size (what you wrap it on):16 gauge needle
Number of Coils: 7/8
Measured Ohms of coil: ~1.0ohm
Wire Type & Gauge: 28g kanthal
Coil size (what you wrap it on): 1/16" drill bit
Number of Coils: 11
Measured Ohms of coil: 1.5 ohm
Kanthal A1 28 awg
1/16 drill bit
10 wraps
1.2Ω on rm2
28 ga
8 wraps
1/16" drill bit
1.0 ohm
Kanthal A1 28 awg
Wraped on .0625" (1/16") music wire
10 coils @ 1.2Ω
28 AWG Kanthal A1
5/4 wraps
1/16 drill bit
0.9Ω
29 Gauge
WIRE: 29g Kanthal
ID: 1.5mm (.0589")
WRAPS: 7/8 x 2
RES: 0.6Ω
. . . . (1.2Ω/ea)
30 Gauge
Kanthal A1 30 awg
Wraped on .0625" (1/16") music wire
12 coils @ 2.2Ω
Kanthal A1 30 awg
Wrapped on .047" music wire
16 coils 2.6Ω ea, total 1.3Ω
Kanthal A1 30 ga
~1/16 jeweler's screwdriver
11 wraps
1.82 ohms
Wire Type & Gauge: 30g Kanthal
Coil size (what you wrap it on): a heavy paperclip leg that's about equivalent to a 16g needle
Number of Coils: 10
Measured Ohms of coil: 1.8
Wire / 30 ga kanthal
coil / size "ID" 1.96 mm "screw driver"
Wraps 7
1.6 ohm
Wire Type & Gauge:30g Kanthol
Coil size (what you wrap it on):1/16 drill bit
Number of Coils:9
Measured Ohms of coil:1.6
Wire Type & Gauge: 30ga kanthal
Coil size (what you wrap it on): Doubled-over 3mm silica
Number of Coils: 4
Measured Ohms of coil: 1ohm
30 ga Kanthal
~1/16 screwdriver
11 wraps pulled really tight while wrapping
1.78 ohms
30 AWG Kanthal A1
13/14 wraps on 1/16 drill bit
Cotton wick
2.5Ω
Wire Type & Gauge: Kanthal 30g
Coil size (what you wrap it on): Supe's 17g needle (Thanks Supe!)
Number of Coils: 10
Measured Ohms of coil: 1.9
wire: 30ga Kanthal A1
size (ID): 16ga blunt tip luer lock needle
# wraps: 12
resistance: 2.3Ω
32 Gauge
Wire Type & Gauge: 32g Kanthal A-1
Coil size (what you wrap it on):Tiny screwdriver, roughly the size of a 16 gauge needle
Number of Coils: 17
Measured Ohms of coil: ~3.0ohm
Kanthal A1 32 awg twisted 2 stands
Wrapped on 1mm Ekowool with .039" (1mm) music wire core
8 coils, 1.1Ω
Wire Type & Gauge: 32g kanthal
Coil size (what you wrap it on): 1/16" drill bit
Number of Coils: 10
Measured Ohms of coil: 2.4 ohm
Wire Type & Gauge: 32g Kanthal
Coil size (what you wrap it on): my trusty paperclip leg
Number of Coils: 14 or 15?
Measured Ohms of coil: 3.8
Wire Type & Gauge: 32 gauge twisted
Coil size (what you wrap it on): round wooden toothpick
Number of Coils: 6
Measured Ohms of coil: 1.4
Last edited:
The one point I read about this morning that toasts my cookies is that after the 75 day comment period, some regs go into effect. Mfg have up to two years to apply to FDA for approval (think this includes devices, not clearly stated in article) and after that it will be the same process as for tobacco companies getting new products approved.
Also, the liquid makers are going to have to disclose all the ingredients to the FDA, but not to the public. This last one is MAJOR BS. That is the ONE thing we, as vapers, need above all else. So all the secret sauce stuff that can hurt us or addict us will be known to the FDA but not the public. Big tobacco is in on this one. And Pharma. Big brother control and watch the money and lobbying.
Have you tried calling any shops? They usually have all the colors still.
Sent from my Galaxy S5 using Tapatalk
This right here is why I got into DIY. I can't fly by the seat of my pants anymore and trust that everything in commercial juice is safe for me. (Recently diagnosed sudden onset insulin dependent diabetic). So if these places are using the "all natural" (read fruit extract, sugar, etc.) Ingredients without me knowing exact ingredients this could be very detrimental to my health. I wonder how these new regs are going to affect that part of the market.
Last edited:
One of the used ProVarii I got off the classies last week arrived FILTHY. I just used Eddard's cleaning technique and WOW so sparkly and vaping like new. Now to do all my others!
- Status
Similar threads
