Tilemahos new rebuildable part (springomizer)
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
Really Ariel, what was it called? Do you remember?
While I'm at it - what's the difference between v2 and v2 plus?
I always assumed it was just that you could fit your own tip... But then I saw a V2 solid mouthpiece, so I guess I assumed wrong...
Sent from my iPad using Tapatalk
While I'm at it - what's the difference between v2 and v2 plus?
I always assumed it was just that you could fit your own tip... But then I saw a V2 solid mouthpiece, so I guess I assumed wrong...
Sent from my iPad using Tapatalk
main differences between v2 and v2+ are:
v2 airhole 2.5mm
v2+ airhole 2mm
v2 liquid channels 3mm
v2+ liquidchannels 4mm
v2 gg engraving at base
v2+ wings engraved on the (clear)tank
v2 airhole 2.5mm
v2+ airhole 2mm
v2 liquid channels 3mm
v2+ liquidchannels 4mm
v2 gg engraving at base
v2+ wings engraved on the (clear)tank
Thanks brem and imeo.
Now - how about that taller tank for 21mm Tilemahos?
Sent from my iPad using Tapatalk
Now - how about that taller tank for 21mm Tilemahos?
Sent from my iPad using Tapatalk
I got my springomizers today and I'm not sure. The taste is not quite right. My first build so maybe the next one will be better.
I also like mine airer but don't have a 9mm inside diameter fat washer and cannot get here in Cyprus to try imeos trick for better air. This is a problem for me.
Just have to see how the next build works out
I also like mine airer but don't have a 9mm inside diameter fat washer and cannot get here in Cyprus to try imeos trick for better air. This is a problem for me.
Just have to see how the next build works out
Here's a shot of the different versions, minus the springomizer as they are in use 
So far so good with the springomizer! Been using them for almost 2 days now and they are working great!! Flavor is the same for me!
Another fine job Imeo!!!
Thank you!!!
So far so good with the springomizer! Been using them for almost 2 days now and they are working great!! Flavor is the same for me!
Another fine job Imeo!!!
Thank you!!!
a quick observation... i tried to make a parallel coil like Imeo does in the video but putting 2 springs together and trimming them. i got a coil that was around .6ohms. i wicked it, primed the wick, and took a a few hits off it and noticed it tasted harsh and borderline burnt. i opened my juice control all the way and was still having the problem. i took the tank and mouthpiece off, primed the wick again and fired it to see what the coil was doing. some of the wraps started to glow red. i fiddled with the spring a bit and repositioned it making sure in was in the posts properly and that no ends of the spring were touching the housing. i again primed the wick and fired it (while blowing on the coil) and the same thing happened, some of the wraps started glowing red. i'm not sure if did something incorrect, but i haven't had any issues like that when running it with just one spring as the coil. maybe some of you are having the same issue, so i just wanted to put it up here.
This one (remove the spaces):
shop . gg-store . com/es/tilemahos-v1-spare-parts/776-tilemahos-v1-longer-tank-shined-only-for-tilemahos-21mm-45ml . html
did you clean the spring yaya?I got my springomizers today and I'm not sure. The taste is not quite right. My first build so maybe the next one will be better.
I also like mine airer but don't have a 9mm inside diameter fat washer and cannot get here in Cyprus to try imeos trick for better air. This is a problem for me.
Just have to see how the next build works out
And what resistance did you make?
Also, did you cut totally flush the wick?
Last edited:
Yes Ariel. Thanks. That'd do the trick... Would need a new mouthpiece too I imagine. If it ever becomes available again...
Sent from my iPad using Tapatalk
That depends on your definition of need. It was designed to have just enough room to grip the MP when it is closed. And with your juice control open you should be ok. Unfortunately I was unable to get one when they were available but that was the idea.
Hi Dontknow,
you don't need a new mouthpiece if you have the solid mouthpiece of the Tilemahos V1
https://www.e-cigarette-forum.com/f...-rebuildable-part-springomizer.703155/page-20
Look my photo it's a long tank with original V1 mouthpiece, just 5mm shorter outside
you don't need a new mouthpiece if you have the solid mouthpiece of the Tilemahos V1
https://www.e-cigarette-forum.com/f...-rebuildable-part-springomizer.703155/page-20
Look my photo it's a long tank with original V1 mouthpiece, just 5mm shorter outside
I received my Springomizer yesterday, cleaned it and made my first buid on it, but I'm not sure yet to prefer it to the regular Tilemahos...
I got the v 2+ springomizer, and it's not as airy as the v 2. Maybe that affects my vape more than I thought, because I find the draw to be a bit too tight for my taste.
The really good point is that it's perfect for juice, as I don't have the problems I sometimes had before (dry hits sometimes, with some juices). I guess the bigger chanels are a real plus, and the 2.9mm internal diameter of the spring (I coiled at a 2.5mm diameter), and I ude Fiber Freaks density 2 for my wicks.
First, I'm a bit disapointed with the springs, as they're said to be aroud 1.2/1.4 ohms, but I can't go above .7/.8 ohms with the ones I got (tried 4 out of the 8 I orederd...). So it's a it low compared to what I'm used to.
Moreover, I'm a bit surprised with the efficiency of the coil : I usually coil my Tile from .9 to 1.1/1.2, depending on the mood I'm in when I recoil. So, my sxeet spot is around 1 ohm.
Now, with springomizer, I'm between .7/.8, so 25% lower.
But surpinsingly, It's not that hotter, and vapor production isn't that much bigger.
So, what concerns me much is that I don't really see the interest of doing lower coils if results in terms of vape are lower too?
Maybe that is only due to airflow, but I'm not sure. I'll have to try the more airy trick to see if that plays a role, but first build ain't that gorgeous for me...
I got the v 2+ springomizer, and it's not as airy as the v 2. Maybe that affects my vape more than I thought, because I find the draw to be a bit too tight for my taste.
The really good point is that it's perfect for juice, as I don't have the problems I sometimes had before (dry hits sometimes, with some juices). I guess the bigger chanels are a real plus, and the 2.9mm internal diameter of the spring (I coiled at a 2.5mm diameter), and I ude Fiber Freaks density 2 for my wicks.
First, I'm a bit disapointed with the springs, as they're said to be aroud 1.2/1.4 ohms, but I can't go above .7/.8 ohms with the ones I got (tried 4 out of the 8 I orederd...). So it's a it low compared to what I'm used to.
Moreover, I'm a bit surprised with the efficiency of the coil : I usually coil my Tile from .9 to 1.1/1.2, depending on the mood I'm in when I recoil. So, my sxeet spot is around 1 ohm.
Now, with springomizer, I'm between .7/.8, so 25% lower.
But surpinsingly, It's not that hotter, and vapor production isn't that much bigger.
So, what concerns me much is that I don't really see the interest of doing lower coils if results in terms of vape are lower too?
Maybe that is only due to airflow, but I'm not sure. I'll have to try the more airy trick to see if that plays a role, but first build ain't that gorgeous for me...
Buying it from you for €5 was just a joke
I know, I know, I was joking, too!
And I'm not selling anything!
It probably is a wicking problem, indeed.
Anyway I opened the juice control a lot, almost at the limit, and.... yup. It's ok. Still not on par with the standard Tilemahos for me but way way better - no strange taste at all.
Yes, obviously it gets discoloured, ultrasonic bath was the first thing I tried.
I just hoped to be able to get it shiny as happens with Kanthal wire; it's not a big issue I suppose, as long as I get it gunk free.
It's true, maybe it's just about changing habits a little bit.
Hey Imeo, thanks for the video suggestions! Really appreciated!
I will try to find a proper oring and try as you showed, for sure.
All in all I didn't give up on this and I plan to update other GG atomizers, too, when the other springomizers become available. It's too easy and quick to build this, and that is very important to me, even crucial.
I know how to make coils, they work fine, but sometimes I'm just in a hurry, I'm tired, I don't want to mess around with wires and pliers, and screws - you know, all that stuff.
Two evenings ago I was cleaning the Penny V4 coil and by scrubbing I broke it - fine. Let's make another one - I broke the wire. Ok... Again. Wire broken.
...
You know these moments when nothing goes the right way, yes?
Third attempt was ok, changing a spring would have been way easier.
Actually, kale mou, I was so excited to try it out I forgot to clean. Right now I have springs and update in the ultrasonic cleaner. I think I cut wick flush but will be more careful with my next build in about half hour.
.Resistance ~ 0.7ohm
bbr, if you want to go higher in ohms, put only 2 threads on the one post and 2 on the other post. Or one thread to every post
We were amateurs all these years Lo Zio and we learned to make coils with bolts, screwdrivers, wires, to be careful when we put wick inside etc. These days are over. We live in 2016, not at 1950 lol. It was about time to find the right way for the coilsI know, I know, I was joking, too!
And I'm not selling anything!
It probably is a wicking problem, indeed.
Anyway I opened the juice control a lot, almost at the limit, and.... yup. It's ok. Still not on par with the standard Tilemahos for me but way way better - no strange taste at all.
Yes, obviously it gets discoloured, ultrasonic bath was the first thing I tried.
I just hoped to be able to get it shiny as happens with Kanthal wire; it's not a big issue I suppose, as long as I get it gunk free.
It's true, maybe it's just about changing habits a little bit.
Hey Imeo, thanks for the video suggestions! Really appreciated!
I will try to find a proper oring and try as you showed, for sure.
All in all I didn't give up on this and I plan to update other GG atomizers, too, when the other springomizers become available. It's too easy and quick to build this, and that is very important to me, even crucial.
I know how to make coils, they work fine, but sometimes I'm just in a hurry, I'm tired, I don't want to mess around with wires and pliers, and screws - you know, all that stuff.
Two evenings ago I was cleaning the Penny V4 coil and by scrubbing I broke it - fine. Let's make another one - I broke the wire. Ok... Again. Wire broken.
...
You know these moments when nothing goes the right way, yes?
Third attempt was ok, changing a spring would have been way easier.
- Status
