Tootle Puffers, Part Three! (The Sequel of the Redux)

[Sugar_and_Spice]

AND matchy matchy! As opposed to my line up of misfits this morning!


Sent from my iPhone using Tapatalk

Nothing wrong with adding a touch of class to your vape..

 

[brewbear]

BB, how long have you had, what is the air like (you know I like it uber tight!), what build you put in it, etc. Inquiring minds want to know

Had it since Saturday. I put a Tricro coil in it, roughly 0.8 ohms I don't remember a non-bf pin, the bf pin was installed. It has a drip tip (rather decent but not ming) extra 510 pin insulator. Decent flavor, 18 mm diameter, 1.0 mm single airflow. If you have a Vicious Ant Cyclone (not the AFC, the first one) this little sucker is slightly more restricted so I think you'll like it. I have it on a aluminum CopperVape.

 

[ToolmanTexas]

Had it since Saturday. I put a Tricro coil in it, roughly 0.8 ohms I don't remember a non-bf pin, the bf pin was installed. It has a drip tip (rather decent but not ming) extra 510 pin insulator. Decent flavor, 18 mm diameter, 1.0 mm single airflow. If you have a Vicious Ant Cyclone (not the AFC, the first one) this little sucker is slightly more restricted so I think you'll like it. I have it on a aluminum CopperVape.

1 mm single airflow!!.. hallelujah!

 

[brewbear]

1 mm single airflow!!.. hallelujah!

Make sure it is the "YFTK Speed Revolution", there are a few others popping up now.

 

[ToolmanTexas]

Make sure it is the "YFTK Speed Revolution", there are a few others popping up now.

Yeah, saw the one for $8 also but no reviews yet. The YFTK has decent rating. In the cart.

 

[Plettschner]

I sense enabling....

 

[brewbear]

Yeah, saw the one for $8 also but no reviews yet. The YFTK has decent rating. In the cart.

Have you looked at the Hussar Copper Vape "edition"? It has an optional top cap fpr 510 DT, Micro tank set kit and a 1.3 mm center pin kit

 

[brewbear]

I have the Speed Rev. on one mech and the Cyclone on another comparing them side by side. As soon as the room stops spinning, I'll be back!

 

[ChelsB]

Does anyone have any tips for pulling an RDA apart? Mine are so snug that I feel like I'm going to damage the mod. Today I almost broke my ohm reader pulling off a dripper cap. I can't seem to get to the bottom of the RDA unless it's screwed into something.


Sent from my iPhone using Tapatalk

 

[petrotech]

Does anyone have any tips for pulling an RDA apart? Mine are so snug that I feel like I'm going to damage the mod. Today I almost broke my ohm reader pulling off a dripper cap. I can't seem to get to the bottom of the RDA unless it's screwed into something.


Sent from my iPhone using Tapatalk

make sure the o rings are lubed up. i have to use a small pair of channel locks wrapped in a paper towel sometimes

 

[ChelsB]

Were you going to comment on that, petro? I don't see a reply....
ETA never mind, I see it know. How weird!

Sent from my iPhone using Tapatalk

 

[petrotech]

Were you going to comment on that, petro? I don't see a reply....


Sent from my iPhone using Tapatalk

fixed it.

 

[ChelsB]

make sure the o rings are lubed up. i have to use a small pair of channel locks wrapped in a paper towel sometimes

Am I being paranoid thinking it could damage the mod if I pulled too hard?


Sent from my iPhone using Tapatalk

 

[brewbear]

Does anyone have any tips for pulling an RDA apart? Mine are so snug that I feel like I'm going to damage the mod. Today I almost broke my ohm reader pulling off a dripper cap. I can't seem to get to the bottom of the RDA unless it's screwed into something.


Sent from my iPhone using Tapatalk

I have an old "El Cheapo" mech mod I use to pull the cap off RDAs for the first time. The only one I bought that was butter smooth was the Nuppin.

 

[ChelsB]

I have an old "El Cheapo" mech mod I use to pull the cap off RDAs for the first time. The only one I bought that was butter smooth was the Nuppin.

Aha! I just threw my ego one VT base away in the battery recycling at work. They rarely empty it, so I'll pull it out tomorrow! That's genius, thanks!!


Sent from my iPhone using Tapatalk

 

[cats5365]

Am I being paranoid thinking it could damage the mod if I pulled too hard?


Sent from my iPhone using Tapatalk

I would worry about breaking something if you need that much force. Do you have any of the threaded tank stands? You could still break something, but the stand will give you something for better grip.

 

[ChelsB]

I sense enabling....

I'm trying to think if I've seen posts of people trying to talk a person out of making a purchase. I can't think of a single one!!


Sent from my iPhone using Tapatalk

 

[ToolmanTexas]

Have you looked at the Hussar Copper Vape "edition"? It has an optional top cap fpr 510 DT, Micro tank set kit and a 1.3 mm center pin kit

That full kit is on its way on the slow boat

 

[ChelsB]

I would worry about breaking something if you need that much force. Do you have any of the threaded tank stands? You could still break something, but the stand will give you something for better grip.

Another genius idea. [emoji4]As a matter of fact, I just got 5 threaded ones last week!


Sent from my iPhone using Tapatalk

 

[brewbear]

Aha! I just threw my ego one VT base away in the battery recycling at work. They rarely empty it, so I'll pull it out tomorrow! That's genius, thanks!!


Sent from my iPhone using Tapatalk

A hybrid mech mod will be sturdier.