-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
Tootle Puffers, Part Three! (The Sequel of the Redux)
- Thread starter Katdarling
- Start date
- th_trl_thread_readers 35
OK, fiddling with the settings on the coil wrapping calculator is making things more lucid for me... great to be able to see what changes going in do to the heat coming out. Thanks again for the info... at this rate, you people will have me building coils by the weekend.It has to do with the and heat flux and heat capacity of the coil, you need to factor in wire surface area and mass. More to it than just ohms law 20W is 20W.
Do you use Steam Engine for your coils builds? All the info you need is there.
Coil wrapping
6 wraps of 28g SS316L
Heat flux @ 20W is 367 mW/mm²
Heat capacity 17.49 mJ/K
6 wraps of 32g KA1
Heat flux@ 20W is 714 mW/mm²
Heat capacity 4.62 mJ/K
ETA:
The higher the Heat flux the hotter the vape, the lower the Heat capacity, the faster the coil heats up.
I try to keep all my builds around 250 with regards to Heat Flux for a nice warm vape.
It will always happen 5 minutes after you have left home for the day. Never when you are at home.
My Dad had a BIG belt...
I had a fear of that BIG belt...
Never a belt here. My dad had big hands.
It is, buy not one that the Smoke XPRO M80 Plus will recognize as such. That mod only recognizes Ni200.
Sent from my SAMSUNG-SM-N910A using Tapatalk
My father used his belt once.My Dad had a BIG belt...
I had a fear of that BIG belt...
Just once...
Sent from my SAMSUNG-SM-N910A using Tapatalk
I know the feeling well. I also hate when I drop the little pieces and then I have to hunt on my hands and knees on the floor. Doesn't help that my woman's cave is a disastrophy!
I'm really looking forward to getting the pro vari. I just can't seem to make friends with the Smok!
At least I was prepared... I've always been paranoid about being vapeless. Keep a spare coil head and a spare whole PT3 in the coin pocket of my jeans... plus a iCare in my front pocket... plus an old Gemini top coil tank in my car in case all feces hits the air circulation machine (honestly, I just left it there from about 2 years ago... it's probably solidified inside)
What a waste of good coil's but I am not going to use those anymore. I will not be using this tank until I get some VCT coils . Hopefully that will solve the problem
Too bad there's not a place where people can bring the stuff that they don't want. Because what you might not want, I may want and vice versa[emoji4]
Lay a towel or a tray with a lipped edge on the table your working on.Yer stuff is less likely to roll/fall on the floor.I do all my recoiling ontop of a styrofoam plate.
I don't think its that at all has more to do with respect some people don't want to see that. I have no problem with it but have a friend that is totally against it so out of respect to her I do not cuss around her. I'm sure there are people on here that have the same problem.
I was totally amazed by Provari today. On Dec. 3rd I ordered a 2.5 full size so I could try 18650's but in the afternoon got an e-mail from Brandy at provari saying they were out of 2.5's but might have some mink's and let her know what I wanted to do. Well I went and looked and they were out of stock so I e-mailed her back and told her they were out. She e-mailed me back and said she beleived they put one back for me if I wanted it let her know, sent a e-mail back and said yes that would be fine. E-mailed me back and said yes they did hold one back for me and everything was taken care of few min. later got order confirmation few hours later got shipping notice now just waiting on pick up. I've heard how good their customer service is but this just blows my mind. This appears to be the last one and to hold it just in case I would want it and possible miss a sale I don't think too many companys would do that. Sorry so long just blow me away
Last edited:
Similar threads
