Tootle Puffers, Part Three! (The Sequel of the Redux)

[pufZeppelin]

All I have are iPhone adapters. But maybe if I try plugging it into the wall that will help?

Lesson: get down in close AND READ whats on the wall adapter and see WHAT the OUTPUT is... (red dots)

 

[ChelsB]

That's a 2A wall wart.Usually used with iPads. Also works with iPhones. If your mod cannot pull 2A, it will simply pull whatever it was designed for, likely 1A. You won't really speed it up with this. And the rate of charging is like boiling water. It will never happen while you're watching.

Just leave it for a bit and come back in a few hours to see what it did.

Thanks, Eskie. Is there anything you don't know about vaping? I see you all over the site answering all sorts of questions

 

[Eskie]

Thanks, Eskie. Is there anything you don't know about vaping? I see you all over the site answering all sorts of questions

Me? Hell no. There's way more I don't know than do know. I just try to learn from all the mistakes I make while sopping up spills or dealing with a short from the coil touching the chimney and whatnot and try to not do it again. Lotsa lessons that I learned the hard way. That, and reading so much helpful stuff around this place.

 

[petrotech]

Me? Hell no. There's way more I don't know than do know. I just try to learn from all the mistakes I make while sopping up spills or dealing with a short from the coil touching the chimney and whatnot and try to not do it again. Lotsa lessons that I learned the hard way. That, and reading so much helpful stuff around this place.

I don't learn anything unless I it up at least three times.

 

[englishmick]

I also loosened all the connections that have O-rings to avoid compressing them since some things are stored away potentially for years. I dont know if that helps any but it's a precaution.

Thanks for mentioning that. I think I saw the same suggestion way back but forgot to do it.

Do you think it would be a good idea to rub a bit of VG on the rings? I picked up a PT mini once, one of the rings had stuck to the end of the glass so firmly that I couldn't get it off without damaging it.

 

[Plettschner]

Krisma suggested that after filling (and don't fill it too full) to close (?) the airflow and just leave it alone - just when you think you want to try it, leave it some more. Give it time to REALLY saturate the wick. Should help with both spitting/gurgling and some flavor. I don't have the 1.5 coils - I'd ordered <1.0 for mine. They can be quite nice, but just take some time to "get ready".

Let it sit since last night... blerg... same poor flavor as my iSub V, almost as bad as the Tesla Shadow 2ml tank. It also came with a sub- ohm coil. Maybe I'll have to try that before tossing it the box of unloved vape gear.


Sent from Uranus using Tapatalk

 

[sorrynomore]

So far winter has been very brown. Only a couple of snowfalls that needed shovelling.

Yup...and I love not shovelling,a great winter so far

 

[TrollDragon]

Yup...and I love not shovelling,a great winter so far

This was last last year, not looking forward to repeating that...

The lower ones are balconies and windows on the second floor.

First pass on the the walkway, the wind leveled it out a fair bit before I started shoveling...

 

[ChelsB]

While I wait for further info, is this too low for a PT?

 

[ChelsB]

Now it's at .96? I don't get it

 

[ChelsB]

Now it's at .96? I don't get it

all I did was turn it off for like five minutes and come back again and it was that much of a difference. Can someone help me understand why that happened?

 

[brewbear]

It is probably touching the coil wall and shorting. At least that's what it looks like from my perspective (right side).

 

[MikeADore]

While I wait for further info, is this too low for a PT?

Looks like it's touching on the right side. Is it?

 

[sorrynomore]

Chels it looks as though the side of the coil is touching the side.

 

[ChelsB]

Grrr... I wish I could say the f word right now. I just went to try to squeeze it in a little bit and pressed to hard and now the coil is all f'ed up

 

[brewbear]

Try to re-insert the mandrel thru the coil and reshape it.

 

[ChelsB]

TBH with you, I hardly ever make a successful coil for my bf RBA or aio coils. Out of every 10 bad ones is 1 good one.
Does it really take this long to make great coils or am I just inadequate in this area?

 

[brewbear]

It takes a lot of practice, just stick with it. Getting a coil jig helps also.

 

[sorrynomore]

Try to compress the coil abit more.

 

[ChelsB]

TBH with you, I hardly ever make a successful coil for my bf RBA or aio coils. Out of every 10 bad ones is 1 good one.
Does it really take this long to make great coils or am I just inadequate in this area?

Of course the hardest part is wrapping the wick around