Tootle Puffers, Part Three! (The Sequel of the Redux)

[Frenchfry1942]

Anker hassome good charging hubs. I was just snooping on them.

 

[Two_Bears]

The only reason I bought them is because they are so cheap they are sitting in my vapocalypse stash. I bought 4 of them

Back in the day Provaris cost $150.

 

[ChelsB]

Back in the day Provaris cost $150.

Wow, what a difference!

 

[ChelsB]

How long did it take you all before you started wrapping really great coils?

 

[Two_Bears]

My box says 250 degrees for 5 hours.

You can revive silica gel in tge microwave too.

 

[brewbear]

Back in the day Provaris cost $150.

They still do! At least the Procyon does! I could get a P2.5 but don't really want to play with button top batteries too. It's bad enough with the 18650 and 26650.

 

[brewbear]

How long did it take you all before you started wrapping really great coils?

Not to brag, but maybe an hour or less. I also make my own jump rings for chain maille, have been doing that for a couple of years prior to my vaping.

 

[Two_Bears]

Omg, that worked!!!!!!

Stay around you will learn all kinds of tips and tricks

 

[Two_Bears]

You have to take into consideration the charging circuit in the device. Most only charge the battery well below 1A. A good charging circuit will charge at 1A. There are very few, if any that charge over that. You can supply it with 20A but the charging circuit is only going to pass through what it's designed to.


Sent from Uranus using Tapatalk

I know. Depends on curcuit in device

But many of the newer devices allow for 2 amp charging. But yoy can't get 2 amp charging with a 1 amp wall plug.

 

[Krisma]

How long did it take you all before you started wrapping really great coils?

Pretty much everrything I change coils in require Non resistant legs. I couldn't be bothered with making the joined wire so I buy ready mades. If I do make coils i use a 14 guage blunt needle 7 wraps on 30-32 gauge Kanthal It didnt take long once I got the hang of it.

 

[ChelsB]

Pretty much everrything I change coils in require Non resistant legs. I couldn't be bothered with making the joined wire so I buy ready mades. If I do make coils i use a 14 guage blunt needle 7 wraps on 30-32 gauge Kanthal It didnt take long once I got the hang of it.

I guess I should stay away from 26 and 28g for a while. 30 seems easier to use

 

[Krisma]

I guess I should stay away from 26 and 28g for a while. 30 seems easier to use

Its about how you vape. I need fast heat because I take small vapes. It suits me...... 32 is actually hard because its so thin. You need to play around with how they work in your device with your style of vaping.

 

[Two_Bears]

How long did it take you all before you started wrapping really great coils?

Just takes practice and patience

 

[corn flakes]

It's plugged into this mess. Please excuse my dirty carpet. I dropped a bunch of Pepsi on there I can never get it out

Well there is a fire looking for a place to happen.

This was last last year, not looking forward to repeating that...

The lower ones are balconies and windows on the second floor.

First pass on the the walkway, the wind leveled it out a fair bit before I started shoveling...

You do tend to get clobbered down your way. I am just off the snowbelt.

How long did it take you all before you started wrapping really great coils?

I made a good coil once.

 

[WillyZee]

How long did it take you all before you started wrapping really great coils?

3 years ago I tried 7 wraps of 30g on the little blue screwdriver ... I still make the same coils today for my Kayfuns 1.7 ohms


Sent via iPhone

 

[TrollDragon]

@Two_Bears, tell me you really didn't try wicking with Dacron???
Dacron wicking. | E-Cigarette Forum

 

[TrollDragon]

We rarely get snow like that in the Niagara region.....every once in a bunch of years though we can.

I used to love touring around the Niagara Region when I lived in Toronto.

 

[TrollDragon]

You do tend to get clobbered down your way. I am just off the snowbelt.

That we do!
I remember when I was little, the snow would always be up to the top of the barbed wire fences in the fields.

 

[TrollDragon]

Only one "I" like out of that post. YMMV


Ummm Yes, But Not really, This has NO BATTERY.
$3.97 Variable Voltage USB Passthrough for E-Cigarette at FastTech - Worldwide Free Shipping (I have a couple, just in case )

You are not going to get very much out of a computer USB port with that thing. They recommend a 2A wall wart to power it.

CE5 with a 2.4Ω coil maybe?

 

[Two_Bears]

@Two_Bears, tell me you really didn't try wicking with Dacron???
Dacron wicking. | E-Cigarette Forum

No. I used Rayon. I couldn't think of Rayon at the time i wrote that message and Dacron leapt to mind