Upgrade from Joyetech ego one

[VapeonLivelong]

Hi guys,
I've been using the joyetech ego one 2200mah, since almost a year now.
I'm planning to upgrade to something new.
Now since i'm not well versed with ohms etc, i would be rebuilding.
But would be re wicking.
So i'd prfer something which has a clr coil head.

Any idea, suggestions would be great.
Cheers!

 

[Eitje]

You want to change just the tank or also the mod?

 

[VapeonLivelong]

Maybe both. First I plan to change the tank. Then the mod.

 

[Susan~S]

Now since i'm not well versed with ohms etc, i would be rebuilding.
But would be re wicking.
So i'd prfer something which has a clr coil head.

So you are looking for a tank that can use stock coils, but also has a RBA base that you can build on (like the Kangertech Subtank Mini)?

On the subtank Mini the stock coils are not rebuildable but you can rebuild/wick using the RBA base.

 

[VapeonLivelong]

Hi,
In the ego one all I used to do is replace the cotton. Because it was a clr coil head. Subtank mini I've no clue about it.

So you are looking for a tank that can use stock coils, but also has a RBA base that you could rebuild & wick the coils you build on the RBA base (like the Kangertech Subtank Mini)?

So you are looking for a tank that can use stock coils, but also has a RBA base that you could rebuild & wick the coils you build on the RBA base (like the Kangertech Subtank Mini)?

 

[Susan~S]

Hi,
In the ego one all I used to do is replace the cotton. Because it was a clr coil head.

So you don't want to build your own coil, you just want to replace the cotton?

If that is the case, then I think your only option (unless someone else knows differently) is to buy a tank that can use the Joyetech CLR coil head. The only tanks I know of that can use this coil head are Joyetech tanks (like the Delta II).

 

[PolishVape]

Get yourself one of these:
- Subtank Mini with RBA base
- Uwell Crown with RBA base
- SMOK TV4 mini with RBA base
All you'll have to do is to change the cotton inside the inner barrel of the RBA base. Try one of these Subohm tanks.

 

[VapeonLivelong]

So you don't want to build your own coil, you just want to replace the cotton?

If that is the case, then I think your only option (unless someone else knows differently) is to buy a tank that can use the Joyetech CLR coil head. The only tanks I know of that can use this coil head are Joyetech tanks (like the Delta II).

The thing is i'm not sure how you rebuild a coil. So either i've to continue with the ego one. Or buy something similar to the ego one.

 

[Susan~S]

The thing is i'm not sure how you rebuild a coil.

Here's a video on how to rebuild the coil => Ego ONE CLR Head Rebuild

You would need to purchase an ohm reader (to check the resistance of your build and make sure you have no shorts) and some Kanthal A1 wire.

You can use Steam Engine to plan your build.

 

[VapeonLivelong]

I did go to steam engine, but its quite confusing since I'm new to rebuilding.
So l probably buy a Kanthal A1 28 gauge, and an ohm reader. Do a few wraps n hope that it comes to 1ohm.

 

[sparkky1]

The thing is i'm not sure how you rebuild a coil. So either i've to continue with the ego one. Or buy something similar to the ego one.

Authentic Aspire Cleito Sub Ohm Tank Kit Top Filling 3.5ML Capacity Silver
Vaporesso Target 75VTC Starter Kit TC VW Box Mod Silver Authentic
Authentic Uwell Rafale Sub Ohm Tank Top Fill 5ML Silver
Joyetech eVic-VTC Mini V2 75W Full Kit TC VW Box Mod White Authentic

 

[Douggro]

I did go to steam engine, but its quite confusing since I'm new to rebuilding.
So l probably buy a Kanthal A1 28 gauge, and an ohm reader. Do a few wraps n hope that it comes to 1ohm.

SteamEngine isn't that complicated. If you put in the type and gauge of the wire (Kanthal A1, 28 gauge), desired resistance (1Ω), you then play with the value for the inner diameter of the coil to figure out how many wraps of wire it will take to get a coil. Answer = 5 wraps on a 2.5mm bit, or 6 wraps on a 2mm bit.

 

[VapeonLivelong]

Hi guys, So i contacted a dealer and he suggested that i go in for Innokin MVP V3.0 he said i can use the ego one atomizer for the same. He also suggested Kanthal A1 30 gauge. Any other suggestions are welcome. Can i use any other mode for the ego one atomizer?

 

[Paul lamb]

If you like your current setup go for the evic vt with ego one mega nice little simple setup

 

[VapeonLivelong]

I didn't get you. I want more vapour.

 

[Paul lamb]

I didn't get you. I want more vapour.

The evic has a bigger tank temp control and has 60w with a built in lipo 5000mah big battery

It produces a brilliant vape

But so does its litt brother the evic vt mini 75w and then you have big brothers the cuboid and the Rx200

The evic vt' swill offer tanks with the kits to make life easy

 

[Paul lamb]

If you want big vapour then you will need a dual battery mod and a big coiled tank such as the tfv4 the Arctic V8 the herakles plus the list goes on

 

[DebiK]

I love my Evic VTC mini with a subtank mini. The MVP does not have a replaceable battery. When it quits charging, it's just dead. You have to buy a whole new unit. With a replaceable battery unit, you just get a new battery (less than $10) You can also switch back and forth with your batteries, so you always have a charged one. I use Kboxes and the VTC mini.

You can build temperature control coils or regular kanthal coils on the subtank mini RBA. The coils last a long time, so all you have to do is build it once and replace the cotton when it starts tasting bad or gets gunked up. For my KBoxes, I use kanthal on the RBA, for my Evic, I use Stainless steel and Titanium wire. (you can also use the Evic in wattage mode, so you can build Kanthal coils.)