Vapes good, looks bad.

[TheBikeGuy]

I thought I would post a pic of this eBaron on my Grand since I haven't saw any. This thing vapes great, hits hard, lots of flavor, but it looks like it's ready to shoot paint balls or something. I didn't use NR/R/NR. It's just a 2.1 ohm old school coil made out of 30 gauge with a doubled 2mm silica wick. Actually the coil has legs like a granddaddy, so that 2.1 isn't really the same as a 2.1 on something else.

 

[HecticEnergy]

Doesn't look bad to me...
You showed me yours, I'll show you mine:

Sent from my iPad using Tapatalk

 

[Fishcakes]

Hey man, whatever works. If youre loving it, flark everybody else.

Just be careful where you point that thing

 

[TheBikeGuy]

Looks good! I might leave this thing on here a while just because it's different. It probably wouldn't look so much like a co2 canister if I put the regular Spiral top on it.

 

[ReigntheGamer]

I think it looks kind of cool with the scrawlings on the side.

 

[Mrs C]

I'm calling BS on the post title...nothing bad looking in that pic.

 

[TheBikeGuy]

I'm calling BS on the post title...nothing bad looking in that pic.

Maybe it will grow on me. It vapes nice. I using it right now. Still looks like a CO2 cartridge though..

 

[wabah58]

I'll have to take pics of my beater work REO. Should to be able to pull this thread down

 

[Rickajho]

Maybe it will grow on me. It vapes nice. I using it right now. Still looks like a CO2 cartridge though..

Well if you can get it to sploot out some seltzer water I've got a bottle of Dewar's right here.

 

[supertrunker]

It looks fine - but i always shied away from that NR-R-NR deal too. 'Oh buy a wire welder, or just knot it together, it's easy!' Meh.

Why would i buy a mod that i can clean in a sink and then have to spend 40 minutes farting about to make a coil for it? So i run ugly coils, which are easy and reliable.

My only issue with tops like that is - i like to swap driptips.

T

 

[TheBikeGuy]

I haven't decided if I wanna invest in the right wire and and stuff. I was going to buy a box of pre-made coils and some new insulators so I would have some spares. It's pretty much like rebuilding a Protank head, so it isn't that hard. A Protank doesn't usually use NR/R/NR, but they should. Most of the time when people think they are burning their juice, it's the legs of their coil burning their coil burning their insulators. I'm gonna play with it some more, but I'm kinda over rebuilding Protank heads. I've got the original Spiral cap for it too, so I can change drip tips.

 

[supertrunker]

I still have some silver NR wire floating around here someplace! I'd forget all that NR-R-NR hassle and just get a decent bottom fed RDA to build on.

Looking at your first pic - you have an original Reo and so you need something like a milled RM2, or such to fit it. Atty has to be about 14mm. There is a (rather long) sticky thread on this topic at the top of the forum.

T

 

[TheBikeGuy]

Oh, I've got atty's. I was just playing around with this one to see what I thought of it. I've got 2 standard profile RM2s an ERA and this eBaron Spiral with the extra cap.

 

[supertrunker]

I suspect it'll go the same way as my Killer atties and end up in a drawer

T

 

[TheBikeGuy]

Yep, I all most hate to because it vapes really good, better than my others. I'm gonna play with it some more, but I'm not sure it's worth the trouble. The Killer looks like it would be similar, it looks like a smaller chamber though. Maybe more concentrated flavor.

 

[jifjifjif]

Looks ok to me.

Reminds me of the nitrous oxide charger cartridges that my friend used to buy to do whippets. My friend liked doing those.