Vaporesso Target PM30 MTL Pod Mod Kit

Status
Not open for further replies.

Frenkyou

Ultra Member
ECF Veteran
  • Apr 26, 2019
    2,028
    2,138
    56
    italy
    www.svapo.it
    The new PM30 TARGET as well as the entire vaporesso PM product series adopts the Coil GTX in this case new specific coils have been created for restricted Flavor and MTL, this new PM30 has a very simplified use and a bypass type operation that automatically recognizes the Coil GTX inserted, in addition it has three selectable power levels, its built-in 1200mAh battery if we do not overdo it with the vape allows you to end the day especially if you use the coils with the highest resistance value. The addition of a Type-C charging cable reduces waiting times. The refill is facilitated with the patented PTF system.

    Enjoy the reading.

    The package with which the Target PM 30 starter kit arrives has the image of the product on the front, the color of the cardboard seems to be linked to what will be the color of the mod inside, two samples have been sent to me one is Red and the high Viola, in reality, as we will see later, these are very captivating and elaborate color combinations. Always on the front and probably only for the samples sent to the reviewers there is a heart-shaped adhesive label containing the message extra mesh coil (thanks Vaporesso) it is a new 1.2 Ω GTX with Mesh I will test it together with the others.

    The back side of the package shows the specifications, the kit content, the batch number, some warnings, the scratch and check, the anti-counterfeiting double V hologram and the inevitable logos and brands.

    1.jpg


    The most important technologies adopted for this kit are mentioned laterally.

    2.jpg


    The other sides of the pack.

    3.jpg


    The kit includes:
    • 1 TARGET PM30 device
    • 2 Pod PM30
    • 1 Coil GTX Mesh 0,6 Ω (20-30W)
    • 1 Coil GTX Normal 1,2 Ω (8-12W)
    • 1 type C charging cable
    • 1 User manual
    • 1 Warranty card
    • 1 Warning card

    4.jpg


    PM30 Kit Specifications:
    • PTF refill from above
    • Coil GTX
    • Dimensions 22×26.7x117.1 mm
    • POD capacity:
    • 1200mAh battery capacity
    • 3-color LED indicator for residual charge level
    • Power adjustable on 3 levels
    • Type C 5V / 1A charging
    • Auto fire protection 10s the device flashes x 3 times with the color in use
    • Open circuit protection the device flashes x 3 times with the color in use
    • Short circuit protection the device flashes red 5 times
    • Low resistance protection the device flashes red 3 times
    • Overload protection the device when fully charged illuminates the green LED
    • Battery charge indicators green color 70/100%
    • Battery charge indicators blue color 30/70%
    • Battery charge indicators red 0-30%

    5.jpg


    Available colors:
    Red Green Black Silver Blue Purple

    6.jpg


    Exploded view of the product:

    7.JPG


    The combination of colors is bright, the metal part of the frame reflects a lot of light especially the purple specimen, the front side houses a single multifunctional round button, allows you to vape, to change the power delivery on 3 preset levels to depending on the coil used, to read the remaining battery charge and to report any malfunctions, under the vertical button we find the word “VAPORESSO-TARGET-PM30”.

    At the bottom rear below the Vaporesso logo is the Type-C 5V-1A charging socket.

    8.jpg


    The leatherette insert is glued to the frame and hides the screws to open the mod is soft to the touch with a very pleasant mix of colors, in one we find the prevalence of red color, in the other example we find the prevalence of purple color.

    9.jpg


    The compartment to accommodate the pod has 3 small magnets arranged in a triangle and two gold-plated spring pins, the bottom is not flat, this does not facilitate cleaning, you need to use a cotton buds and lose some time.

    The base on which the PM30 rests has the disposal logo, the C E mark, the place of production, an indication of the capacity of the integrated battery and its vent holes.

    10.jpg
     

    Frenkyou

    Ultra Member
    ECF Veteran
  • Apr 26, 2019
    2,028
    2,138
    56
    italy
    www.svapo.it
    The pod:

    It has a flare at the bottom that acts as an airflow (first image below).
    The tip is integrated with the Cap, both black in color, they match well in my opinion with the fume part, this part allows you to see the liquid level without having to extract anything, therefore very comfortable.

    11.jpg


    The opening of the Cap (slide) allows access to the PTF refill system patented by Vaporesso, this system has been introduced for some time on other devices of the parent company and has always worked properly, continues to do so also on this PM30, its spring system provides for the use of the given bottle supplied or in any case of bottles with a spout suitable for a rigid tip.
    In the images below we see the ingenious PTF system together with another image on the visual transparency of the Pod.

    12.jpg


    13.jpg


    GTX coils:

    Those specifications introduced by Vaporesso for the PM30 are the 0.6 Ω GTX Mesh (20-30W) and the 1.2 Ω GTX Normal (8-12W), I also tried the 1.2X GTX mesh (7-11W) and the GTX Mesh 0.8 Ω (12-20W)

    14.JPG


    The coils should not be initialized except with a few drops of liquid and only on the side holes, the part to be followed scrupulously to avoid problems is to wait at least 5 minutes after the refill to give the cotton the opportunity to get wet evenly before starting to vape .

    Below we see some images on the correct insertion of the Coil GTX, Vaporesso indicates the correct insertion as in the photo.

    15.JPG


    16.JPG


    17.JPG


    How the Target PM30 works:
    Operation as already anticipated in the introduction to this article is extremely simplified in fact the device is equipped with a single button.

    To turn on / off the mod, you make five clicks, to vape hold down the button and to adjust the output on three different Wattage, we just press the button three times, each power step is matched with a color depending on the coil inserted, red low power, blue medium power, green high power, at the moment only the steps for the coils supplied in the kit are known; as in the image below.

    18.JPG


    The single button also has the function of checking the battery charge level and this is the diagram.

    • 70/100% green led battery charge indicator
    • 30/70% blue led battery charge indicator
    • 0-30% red led light battery charge indicator

    19.JPG


    General instructions for use:
    It concerns all the devices ... I remember that in the pod devices the coil is in direct contact with the pin not as on the tanks that have a base under the coil that can hold condensate and excess liquids longer, so for each refill just check losing half a second and possibly drying, during the night or in periods when the electronic cigarette remains still, it is advisable to always disconnect the pod or atomizer if there is liquid inside them, because there may be leaks.

    Respecting the recharge values indicated by the manufacturer is important in order not to compromise the functioning of the circuit, therefore it is necessary to avoid using chargers with values other than those indicated by the manufacturer such as those of the supercells. As in any other vaping device, you also need to be a little savvy and know the right ploy to stay calm and enjoy your electronic cigarette.

    Final conclusions:

    Aesthetically this Target PM30 is really beautiful, the leatherette inserts are well-made and coupled without protrusions with the metal of its frame which makes the Mod solid, robust and smooth to the touch. The slightly hollowed front contains even more excellent dimensions and the only control button offers good feedback.

    The chipset is really reactive, it works in bypass, it automatically recognizes the installed coil offering the best yield for its use by simplifying life for the neophytes of the vape, the power can be adjusted in three steps on each coil used, remember; red led low power, blue led medium power, green led high power.

    The 1200mAh battery offers more than good durability especially when used with 1.2 Ω coils

    To refill, only 3 very fast and practical steps are needed thanks to the sliding of the top cap and the patented PTF system.

    The cartridge is easily extracted by pulling the tip and is anchored well to the mod, it will never pop out unless you wish, the liquid inside is clearly visible in normal light conditions.

    — The GTX 0.6 Ω Mesh with 20-30W range included in the Target PM30 Kit is designed for a Restricted Flavor, I find it very balanced as an aromatic yield and the volume of the steam generated is consistent, never too hot. On the battery consumption side it is the least indicated.

    — The GTX 0.8 Ω Mesh 12-20W was introduced by Vaporesso for the PM30 and can be purchased separately, on our PM30 I think it is much more suitable than the previous one because the performance I find very similar, of course to the benefit of the battery life in restricted flavor.

    — The GTX 1.2 Ω Regular 8-12W included in the Kit has a small air-flow hole, but despite this, it still remains an open MTL, in the final shot it can close more especially by aspirating with more vigor, this is not mine preferred in the GTX lot, however it manages to surprisingly produce a lot of steam in relation to the approximately 10W that it delivers, moreover the consumption of liquids / battery is really negligible.

    — The GTX 1,2 Ω Mesh can be purchased separately (but I haven't seen it on sale yet) I like it much more than the previous 1.2 Ω regular, the mesh is more responsive and aromatic and is also more fluid, it also creates more contrast in the puff to the advantage of an MTL vape, practically the two coils sold separately are the ones that I would have put in the kit as the first choice, the 0.8 Ω because it maintains the performance of the 0.6 Ω but reduces its battery consumption to the full advantage of the time since devote to vaping. The 1.2 Ω Mesh instead I would have inserted it as original equipment because it is practically superior in all respects to the 1.2 Regular.

    The new Target PM30 is recommended for those looking for a tight flavor vape, while for those who want to use it in MTL (open enough) I recommend using it only with the 1.2 Ω mesh coil.

    20.jpg


    I thank Vaporesso for offering me the opportunity for this Test: Target PM30 » Vaporesso
     
    Status
    Not open for further replies.

    Users who are viewing this thread