VV Kit

[MXBNW]

I ordered the VV kit not the mod kit just the VV unit alone.

Is there a simple wiring diagram around. I am sure I can make it work but it sure would be faster for me to have one to look at.

Thanks for all your help in advance.

 

[Jetmec]

Variable Voltage Regulator Board Kit Rev 2 If this link works to the mad vapes site

it is what you are looking for I think. Click on the second picture of the kit. Hope this helps.

 

[MXBNW]

Variable Voltage Regulator Board Kit Rev 2 If this link works to the mad vapes site

it is what you are looking for I think. If the link don't work you can find it if you click on the picture of the kit than open the second picture. Hope this helps.

No Link

 

[TomCatt]

From MadVapes website:

 

[Jetmec]

That's it Tomcatt.

 

[MXBNW]

Thanks every one that is just what I was looking for.

Thanks again, Now to build something cool

 

[MXBNW]

Quick question if I am building a stacked battery mod what post do I run the + would it be 2 or 4

Or do I have to wire it as two battery's Or is there an easier way to wire it when using a set of battery's stacked

Sorry for all the questions this is my first attempt at a VV Mod.

 

[TomCatt]

MadVapes = The Modder's Den {=^-^=}

 

[MXBNW]

MadVapes = The Modder's Den {=^-^=}

LOL I get the fever every once in a while to build something this time I need a VV unit to go in to a mod I wont to build.

 

[tybin]

don't blow up the house

 

[MXBNW]

don't blow up the house

LOL If I do I will do it good

you will see it all the way to your house

 

[crk0756]

I love the simplicity of the kit, but if you are a chain vaper, they tend to get a little warm.......

 

[Bluzeman]

Thanks every one that is just what I was looking for.

Thanks again, Now to build something cool

If by stacked you mean inline, like in a tube mod, just put the + of the top battery on pin 2. If they are side-by-side as in a box mod, make sure to wire it so the 2 batteries are in series, and run the + of the second one to pin 2. The only thing that should connect to 4 is the + from the atomizer connector and the center leg of the pot.

D'oh! I quoted the wrong post. Meant to quote this one.

Quick question if I am building a stacked battery mod what post do I run the + would it be 2 or 4

Or do I have to wire it as two battery's Or is there an easier way to wire it when using a set of battery's stacked

Sorry for all the questions this is my first attempt at a VV Mod.

 

[MXBNW]

Thanks Bluzeman

 

[Handthatfeeds242]

ok I am a total noobasaur rex when it comes to modding VV I have done a few 3.7 box mods for friends but I now would like a VV. I am lost on where to place the resistors on the board. I see them called out as R1 and R2 but where do they go? Do they jump from 2-3 and 4-3? any help is greatly appreciated.

 

[hoogie76]

they go right into the holes that say R1 and R2, just picture the body of the resistor goes where the little squares are and legs go right down into the holes at the edges of the squares(after you bend the resistor like a letter U).. Good luck..

hoog

 

[Handthatfeeds242]

So as the yellow lines are would be correct? Sorry for the noobness.

 

[hoogie76]

no problem at all.. you'd want to put them in like this:




hoog

 

[Handthatfeeds242]

Thank you very much. Now it makes sense.


---
I am here: http://maps.google.com/maps?ll=39.988470,-76.728640