Which All Devices does the Protank Replacement Coil/Wicks Fit?

[dodari]

I'm just wondering which all these replacement coil/wick units Kanger ProTank & Davide Replacement Head - 1.5ohm 1 PC [gv-ProTankReplacementHead-1.5ohm] - $1.65 : GotVapes.com, E-cigarette Supplies - Atomizers Cartomizers Mods Juice and more will fit?

I want to order some 1.5 Ohm units but how many to order will depend on what all they fit. Will they fit the EVODS?

Thanks.

 

[rdsok]

I'm just wondering which all these replacement coil/wick units Kanger ProTank & Davide Replacement Head - 1.5ohm 1 PC [gv-ProTankReplacementHead-1.5ohm] - $1.65 : GotVapes.com, E-cigarette Supplies - Atomizers Cartomizers Mods Juice and more will fit?

I want to order some 1.5 Ohm units but how many to order will depend on what all they fit. Will they fit the EVODS?

Thanks.

They do fit the Evod's as the T3s, Mini-T3s... They are a bit different though... they have a longer tube over the coil and they are a little bit airier than the Evod coils.

 

[djezewski]

They do fit the Evod's as the T3s, Mini-T3s... They are a bit different though... they have a longer tube over the coil and they are a little bit airier than the Evod coils.

What I am wondering is do t3s coils fit the Davide, I really want a Davide and would like to put some t3s coils to use

 

[rdsok]

What I am wondering is do t3s coils fit the Davide, I really want a Davide and would like to put some t3s coils to use

I haven't tried a Davide and don't have plans too at this time... but GV's states the ProTank coils fit them and I see no reason to doubt them... and also since Anyvape stole the underlying concept/design from Kanger to start with when building the Davide.

 

[djezewski]

I have the Puritank and it is wonderful and it does take the t3s coils. That was one of the reasons I chose it. I am not sure how much different the Davide is from the Puritank. When I get some funds I am sure I will get a protank2 and a mini Protank2, but I also want a Davide without the hassle of different coils.

 

[dodari]

They do fit the Evod's as the T3s, Mini-T3s... They are a bit different though... they have a longer tube over the coil and they are a little bit airier than the Evod coils.

Thanks rdsok, makes ordering a boodle of the 1.5s more assuring.

 

[Screamin Eagle]

I just put an order in for a Mini Davide and an MT3s along with some replacement coils for the MT3s. When they come in I'll try to see if I can switch out the coils. I think they are the same. I also have an Evod that I can see if things fit on. I'll have to let you know.

 

[woody55]

Just a little FYI, replacement coils being sent out by Kanger for the EVODS now have the long stems. We believe they are moving to a universal head for all the bottom coil units.

 

[Screamin Eagle]

Yep, the MT3S coils (which are the exact same as the ProTank coils) fit the Evod, and the Mini Davide. But I think the Mini Davide is shipped with knockoff coils in it though because the ones that were in there didn't fit well in the Evod or the MT3S. I also found out that the MT3Ses knarled base will thread upto the Evod but it sticks out away from the tube sides just a little.

Does anyone know if the Evod base is suppose to have two o-rings sealing it, or just one? My Evod only has one at the bottom of the base, but there is a grove towards the top where an o-ring would fit. The MT3S on the other hand has 2 o-rings on it's base.

 

[rdsok]

The o-rings on the Evod... One is on the coil head itself just below the flange and above the threads. Then on the base itself ( standing up, coil head on top ) are two o-rings... one just below the thread and one a little ways up from the thread but below where the flange on the coil head meets the base.

 

[rdsok]

Here is the pic from Gotvapes website for the base only for a T3s... it is very similar to what I just described...

 

[Screamin Eagle]

Here is the pic from Gotvapes website for the base only for a T3s... it is very similar to what I just described...

The Evod has a similar base but it's not knurled. I'm not talking about the coil unit. Take that completely out. Does the Evod base have the 2 o-rings like those T3s bases do? Or should I ask is it SUPPOSE to have them. My Evod only has the one on the very bottom. My wifes MT3s has both. My Evod keep flooding. I'm woundering if this seal could be missing causing the problem.

 

[Pitviper]

They work in the Vision Victory also. The stock heads on the victory are actually the same as evod heads. I prefer the airer draw of the protank heads, so I swapped it. Works just as good as a protank, and has a 5ml capacity.

 

[keelalagirl55]

The Evod has a similar base but it's not knurled. I'm not talking about the coil unit. Take that completely out. Does the Evod base have the 2 o-rings like those T3s bases do? Or should I ask is it SUPPOSE to have them. My Evod only has the one on the very bottom. My wifes MT3s has both. My Evod keep flooding. I'm woundering if this seal could be missing causing the problem.

Not sure why I can't get the pic link, but look here EVOD the second picture shows the base of the evod.

 

[rdsok]

The Evod has a similar base but it's not knurled. I'm not talking about the coil unit. Take that completely out. Does the Evod base have the 2 o-rings like those T3s bases do? Or should I ask is it SUPPOSE to have them. My Evod only has the one on the very bottom. My wifes MT3s has both. My Evod keep flooding. I'm woundering if this seal could be missing causing the problem.

I guess you didn't read my post very close... the T3s base is setup the same as the Evod base... I know the T3s is knurled and the Evod isn't... but it is still setup in the same manner. The pic that Keela linked you to will show you also ( but they took the top tube out of the coil )

 

[Screamin Eagle]

I guess you didn't read my post very close... the T3s base is setup the same as the Evod base... I know the T3s is knurled and the Evod isn't... but it is still setup in the same manner. The pic that Keela linked you to will show you also ( but they took the top tube out of the coil )

I just know that some manufactures, when they change tooling, will keep some of the features of the old tooling in order to cut cost and time. Even if the feature isn't used.
But you are right, I wasn't reading what you wrote correctly. Darn those periods, and commas.

Not sure why I can't get the pic link, but look here EVOD the second picture shows the base of the evod.

Thanks for finding that for me Keela. Looks like I got an Evod that was not only missing a coil seal but a base seal as well.