Which Ego to get?
- Thread starter Johnny2puffs
- Start date
- th_trl_thread_readers 0
- Status
milliamp hours or mah is jsut battery life... won't really help with TH. I am a TH-chaser as well... I usually vape 6V at 3ohms. I quickly moved passed the 510s and eGo's into mods... I think if you want TH you really have to go for mods... that way you can use 3.7V with 1.5ohm atomizers or 6V with 3.0ohm atomizers, which will increase TH.
I disagree. mAh is not bat life but bat power. ie a 600mAh bat with a 2ohm resistor (atty) can produce 0.6 amps in 1 hour. Where a 1000mAh bat can produce 1 amp through the same atty in 1 hour. More amps = more heat.
Also Power = Amps X Volts. More resistance, less amps less power.
So if you using 3v bat with 1.5ohm atty is exactly the same as using a 6v bat with a 3ohm atty. Same amperage and same power. No diffs.whatsoever.
Believe me. I am an Electronics Engineering Tutor.
Last edited:
Whats comming and where ??? I am realy in the market for a propper HV mod
I do not believe:
Power = Ampsx Volts = VxI , while
Amps = Volts/Resistance or I = V/R
By Substitution: Power = V x V/R
using 3v bat with 1.5ohm atty Power = 3x3/1.5 = 6 Watt (Current = 2A)
using a 6v bat with a 3ohm atty, Power = 6x6/3 = 12 Watt (Current = 2A)
Even though the current is the same, power is double....
Last edited:
From a 600mAh bat you draw 0.6 amps in one hour with a 2ohm resistor IF you supply it at a voltage of 1.2 V (V= IR)
The power produced will be (Power = VxI) = 1.2x0.6 = 0.72 Watt
From a 1000mAh bat you draw 1 amps in one hour with a 2ohm resistor IF you supply it at a voltage of 2 V (V= IR)
The power produced will be (Power = VxI) = 2x2 = 4 Watt
600 mAh means the battery can supply 600 mA for 1 hour or 1.2 A for 30 mins or 300 mA for 2 hours
1000 mAh means the battery can supply 1000 mA for 1 hour or 2 A for 30 mins or 500 mA for 2 hours
The heat (or Power) supplied by any battery depends on the Voltage and
the Resistance (Power = VxI), not mAh rating . The "mAh" merely indicates the expected battery life - if you know the mA you will draw, you can estimate the time the battery will last.
Last edited:
To respond to the OP - Low Resistance is the best way to get the desired TH for me, and also new atty's of course. After a few days of use atty's seem to get "tired" - reasons and remedies can be found all over the ecf.
I use LR atty's with any eGo type batteries or 510 Pass throughs. Some of the batts do not like the low resistance and cuts out after 2 seconds or so.
I normally rinse and dry burn to revive tired attys - does not always work. But i seldom kill them with dry burn.
I use LR atty's with any eGo type batteries or 510 Pass throughs. Some of the batts do not like the low resistance and cuts out after 2 seconds or so.
I normally rinse and dry burn to revive tired attys - does not always work. But i seldom kill them with dry burn.
Rinse those attys out at least once a week with Surgical spitit and dry burn.... use a syringe that you have bend of the needle part and squirt the spirit hard ofer the coils... work great in my Leo attys... but yes you are right, they do tend to go bland.
Hi, my new Ego T (A) arrived today. Have been vaping my 510 with atty & cartridges for past month.
I think I'll get used to the bigger size of the Ego, but I have to say I am disappointed with the flavour produced. Have tried 2 juices, but both have no flavour when compared to my 510. I think it may be because the vapour is too cool. Thus have ordered a Type B LR atty, which I am hoping will give a higher temperature and hopefully the flavour of my juices will return. I just love my Old Holborn & Coffee flavour.
I think I'll get used to the bigger size of the Ego, but I have to say I am disappointed with the flavour produced. Have tried 2 juices, but both have no flavour when compared to my 510. I think it may be because the vapour is too cool. Thus have ordered a Type B LR atty, which I am hoping will give a higher temperature and hopefully the flavour of my juices will return. I just love my Old Holborn & Coffee flavour.
Nomdo, I fully agree with you. You are correct. I presume you work at SASOL or AECI as an Instrument Techie if they still exist there.
One Amp through a 2.5ohm atty is less heat than 1 Amp through a 5 ohm atty. I forgot that as I am retired now for 15 years from electronics. One Amp was more powerful 15 years ago than it is now.
One Amp through a 2.5ohm atty is less heat than 1 Amp through a 5 ohm atty. I forgot that as I am retired now for 15 years from electronics. One Amp was more powerful 15 years ago than it is now.
Nomdo, I fully agree with you. You are correct. I presume you work at SASOL or AECI as an Instrument Techie if they still exist there.
One Amp through a 2.5ohm atty is less heat than 1 Amp through a 5 ohm atty. I forgot that as I am retired now for 15 years from electronics. One Amp was more powerful 15 years ago than it is now.
yes you are right -- SASOL -- Now how the hell did you figure that out? I wish I was a good at figuring out stuff like that...
anyway, happy vaping!!
Good going with Chemistry. The most difficult career choice when I was at Technicon. I chose Instrumentation. Worked in Analyzer Dept. at SASOL.
- Status
Similar threads
- Locked
