rebuild

Hey, I've been rebuilding Protank heads for a while, but I've never had any way to check Ohms until recently. I used 5 wraps of 32 gauge Kanthal around 2.5mm Silica with a needle or around a cocktail stick for a cotton build. I've been vaping this build for a couple months on basic Ego...

I am going to do my first rebuild on my Aspire Nautilus since I bought it. I will be doing it per the RIP TRIPPERS video. My question is how well this set up has been working for everyone, and more specifically, how long the cotton wick lasts before having to redo it? Just curious what...

Ok, I have looked around and have not found much specifically on this subject. I apologize If I missed a pertinent thread. I purchased one of the aluminum sentinel clones from fasttech and have been reading about the soft threads on it. It sounds like I can basically rely on them stripping...

I am about to purchase a rebuildable atomizer and just need some tips here. I am going to be using it on an MVP2 so I need a higher resistance. I don't know if I should go with 32 or 34 gauge kanthal and I don't know what size wick I should get (anywhere from 1-3mm diameter silica). I know the...

Hey Everyone! I am thinking about getting a Rebuildable dripping atomizer today. I have never built my own atomizer before so I am new to this. I have watched some videos online and it seems simple enough. I have enough common sense to figure it out. I need a recommendation for something that...

Reviewing the famous RiP Trippers video on single-coil + cotton rebuild video of a Nautilus head, I came across a comment by Paul Till with a link to this ingenious mesh rebuild. Since I don't have any mesh and ordering some to try it will have me sitting for a good four or five days unless I...

So I'm now the proud new owner of an NES DNA20 mod from Joe Litt. I took the back plate off to check out how hard it would be to replace the battery later down the road. I noticed The DNA board, and pretty much everything else inside the controller is being held in place by epoxy or "glue"...

I just did my first successful build! I built a dual micro coil on an iGo-W clocking in at about .7ohms and so far I'm quite happy. Since I'm new to rebuilding of course I'm watching all kinds of "how to" videos and questions are starting to swirl around my head. I guess my question(s) are...

As promised, my picture tutorial of rebuilding an iclear 16 atomizer. I only did a single coil rebuild this time around since I'm running low on kanthal and I really want to redo my protank, but the process is pretty much the same. You'll just have more legs to trim and more coils to keep steady...

I don't want to hurt myself or vape pen so I fuigured I better just ask before I started wrapping wire around things :P I'm planning on rebuilding the coil in a protank 2 mini. What wire should I invest in for the coil? Should I use cotton or silica wick? - I read that cotton balls work? Just...

This could be old news to some but I found those rubber gromets everyones always talking about @ Lightning Vapes - All the RBA Materials you need! Silica Wick, Ekowool, Kanthal Wire, Stainless Steel Mesh and more! woooohooooo. No more burnt rubber... lol:evil:

Not sure if this is the right place to post this. Mods please move it if it isn't. I recently started using cotton as wick on my Kanger Protank II and Mini Protank II and have noticed a big increase in throat hit. The throat hit is so much in fact that it leaves me with a sore throat. The...

rebuilt using .5 ribbon....3wraps per coil...two coils sharing 1 strand of 3mm threaded eko.... Trident RBA.....0.3ohm... anyone have recommendations for batteries that have a 20amp rating? this is hitting 14 amps @ 4.2 volts, under load, not sure....I know the AW is good up to 10....Will a...

Getting into the vape groove after a while of meddling about. Now wrapping up solid 1.8ohm coils for my Protank II like coil building ninja. Tried some silica wicks and they were ok. Decided to make the switch to cotton yarn, so found a 100% cotton spool and built it. Vaped pretty good with...

I have an MVP v2 and I am looking for a device that I can rebuild and drip with it. What suggestions would you give me and how much do they cost?

Hi Guys. Not sure if this is the right place for this thread, if not, apologies. So, i've wanted to rebuild heads (T3 at the moment) for a little while now and today finally bought some 3mm silica wick and kanthal wire, I hear 34 Gauge a lot but the packet i bought makes no sense to me, it...

:confused: at the moment, im using a davide mini tank, with the flavor deadly sin. SOME hits seem harsh almost burnt taste. wont dry burning make it worse? im not sure, im new dont hate me for all the questions. But the tank does look a little crooked and it bugs me lol

So I know there's a ton of ways to rebuild an atomizer. And they sometimes have some weird names. Like the mt pinatobu, walking on water, the slug, micro coils, center coils, vertical coils, etc. So I'm looking for you to post your favorite build design with maybe a description or a video on how...

I am rather new to vaping and just got my first RBA - I-Atty v3 from 101 Vape. They also sell it at FastTech. It comes with replacement parts but no instructions. Can anyone tell me or refer me to a video on how to disassemble this device? It is vaping with a terrible taste that burns the...

Can my air hole be too big and causing flavors to seem muted on my AGA-t2? I drilled my air hole to 11/16 which equals to 1.5875 mm air hole. I have read people drill out to 1.2 mm. Is this the reason my flavors are not as flavorful?