t3s

Just bought 1-T3S just to try and several EVOD's because they are easy to rebuild. Also purchased a couple of 650mah Kanger VV Twist batteries... So -The Good ...Batteries are great. Light. Nice size. Work perfectly. Would prefer a button that sticks out a little so you can feel and find it...

I was wondering what type of settings I should use on my Cool Fire 4 with the T3S. The T3S is using a 1.8 ohm Atomizer. I want to know if I should use the Voltage setting or Wattage, and what level one or both should be at. What I'm going for is a big wet hit, not too hot, but enough to fill my...

So how often should I clean my kanger coils? A simple question, but googling it has brought me close to nothing... what are your guys's suggestions (Using the good ol' t3s) Also, I lied about the hamburgers....

Hello everyone! Long time lurker, first time poster. I've gained a wealth of knowledge from the good folks here at ECF over the years and I would like to share a tip or two that I've learned while trying to get the best vape out of one of my setups. I like to give back if I can. Has anyone...

I was disappointed to find that the T3S clearomizer I bought won't fit due to the narrow diameter of the Tesla's housing. I have looked around and found that this is a unique problem. Luckily, they're willing for me to return them, but now on the hunt for something new. Hoping someone has some...

I bought a Kanger T3S about a week ago and once it gets to about 0.6 ml it will start leaking everywhere. Took it back about 2 days ago and asked them about it and they replaced the coil and filled it back up, well about an hour ago it got back down to the 0.6 ml and started doing it again. I...

Hi all! It's been forever since i've posted...but i've got a burr in my saddle! Was using kangar t2 and some wise guys decided to change what was perfectly fine and create t3s. Problem: center post sits too far back and adjustment mid vape sometimes happens! I'm using ego twist and a vv...

For a little over the last week I've been attempting recoils and rewicks of both my EVOD and T3S with varying success, but here's what I've found. Using a 1.3 screw (tried a 4-40 screw and the coils were WAY too big, huge compared to the factory coils, so I'm not sure where the miscommunication...

What's the best way to clean the coil of a Kanger T3S? Some posts suggest vodka, others suggest hot/boiling water, others isopropyl alcohol? What's the best & what's surely not going to damage it? Coils are very expensive where I am (around 7-8$ for _one_ non-Kanger made replacement coil for...

I bought a replacement head after a month of using the stock coil. Its still good as I clean after every tank and replace the flavor wicks with cotton.it is a 2.2 ohm and the one I just bought is 1.8. Now I'm getting burnt flavor a lot. Is it the lower ohms that's causing it? My battery is a...

Hey all Sorry if this is the wrong board for this, but I looked around and this looked like the most appropriate place. I want to start rebuilding my Kanger attys for the T3S and EVOD, but I have very little idea where to start. I've been vaping at 1.8 mostly, and I tried repurposing some...

Hey all, been a while since I posted (a few years it seems like) because I discovered the Ego + CE5 Redux combo and have been in vape heaven ever since. But very recently I decided I wanted a change (that and I can't find a solid redux supplier anymore), and picked up the KangerTech T3S and have...

I guess I didn't read all the fine print. I got 4 T3S clearos because I like the T3 for away from home and I thought the ProTank coils would work with them, thereby simplifying my rebuilding regimen. Wrong. The Evod/PT coils don't fit in the T3S, the metal ring near the base is too large to go...