Genesis atty with SB

Discussion in 'Silver Bullet' started by DFNDR, Jan 1, 2013.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. DFNDR

    DFNDR Senior Member Verified Member ECF Veteran

    Joined:
    Dec 26, 2012
    Location:
    Oklahoma USA
    I'm new to rba's but I bought a couple and want to use them on my SB. Should I just run it at 3.7 with a 18650 or can I run them at 6v with cr123s?

    If I can wrap a coil to 2.5ohm would that be close to my 2.5 ohm carto?

    I have a provari as well but use my SB more.

    Input?


    Sent from my iPhone using Tapatalk
     
  2. Plumes.91

    Plumes.91 Vaping Master Verified Member ECF Veteran

    Joined:
    Jan 30, 2012
    Location:
    United States
    A 2.5ohm coil is a 2.5 ohm coil. A 2.5 ohm coil in a 2.5ohm cartomizer is going to vaporize juice just like a 2.5ohm coil in a RBA. I recommend around 4 to 4.5 volts with a 2.5 ohm anything.

    Do you use your SB with a Kick or do you use it with the 3.7v or 6v batteries? I'm interested. I use my Provari more than any of my other mods but i'm thinking about getting a kicked SB. Why do you like it more than yo Provari?
     
  3. DFNDR

    DFNDR Senior Member Verified Member ECF Veteran

    Joined:
    Dec 26, 2012
    Location:
    Oklahoma USA
    Yeah I've learned the wick and coil game pretty quick. I'm running a .9 ohm coil at 3.7 I have a kick but I don't use it.

    I like my SB better bc you can't hurt it. My profession is kinda rough so I can't risk ruining a provari.


    Sent from my iPhone using Tapatalk
     
  4. KalThaxx

    KalThaxx Senior Member ECF Veteran

    Joined:
    Aug 5, 2012
    Location:
    Cleveland
    I bought a kicked silver bullet, but with these rbas(I have dud, aga t, and Phoenix) I have started using sub 1.2 ohm with 3.7v. I am preparing myself to get into fully mech mods. I will all ways love the SB.
     
  5. DFNDR

    DFNDR Senior Member Verified Member ECF Veteran

    Joined:
    Dec 26, 2012
    Location:
    Oklahoma USA
    Yeah the SB was my first mod (i think) and will always have a place in my hand! Lol.


    Sent from my iPhone using Tapatalk
     
  6. Baditude

    Baditude ECF Guru ECF Veteran

    Joined:
    Apr 8, 2012
    Location:
    Ridgeway, Ohio
    I've got both a Silver Bullet and a Provari. I just received my first rebuildable, the newest version AGA Tiamat Plus with glass tank.

    Since I've had the Provari for about five months, the Silver Bullet has been resting in backup status. I'm thinking of putting the AGA on the Bullet to resurrect it's usefulness.

    I've yet to tinker with the AGA. I'm still gathering supplies that I need, like a minature torch to oxidize the mesh and wire.
     
  7. hanathan

    hanathan Full Member Verified Member

    Joined:
    Apr 3, 2012
    Location:
    Madison, WI
    No need to stack batteries. If you prefer a warmer vape, you could continue lowering the resistance of your coil, but first I'd make sure your wick isn't too long. Stainless steel mesh acts as a heatsink, so the thicker and longer it is, the more difficult it will be to warm up.
     
  8. TattooedSkin

    TattooedSkin Senior Member Verified Member ECF Veteran

    Joined:
    Jan 16, 2013
    Location:
    Las Vegas
    I use a lot of rebuildables and the voltage setting isn't quite like a carto. I use a Z-atty Pro on my provari and with a 1.3 coil I vape it at 5.0v, your wick will determine your voltage. If you prefer a solid mesh wick it most likely wont wick fast enough to ram up the volts. I prefer straw type mesh wicks (hollow) and if I run lower volts, it over wicks and makes a mess.

    With a rebuildables you only limited by you. I would highly suggest to try different setups and you will be amazed at where you end up.
     
: provari
Thread Status:
Not open for further replies.

Share This Page