How much cotton?

Discussion in 'General Vaping Discussion' started by Paradicio, Jun 23, 2014.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. Paradicio

    Paradicio Hazy Verified Member ECF Veteran

    Supporting member
    Joined:
    May 30, 2014
    Location:
    Altadena, CA
    So, I had asked this in another thread but didn't get an answer (I think because answering would derail the thread), so I thought I'd try here with a new post....


    This may be a dumb question, but the builds in those images seem to be using an awful lot of cotton? Is that how much I'm supposed to be using? I'm using about half that much (speaking of thickness, not length).


    Appreciate the help! :)
     
  2. Kracker

    Kracker Super Member ECF Veteran

    Joined:
    Feb 21, 2014
    Location:
    NewCastle, DE
    I try to get as much through the coil as I can without having to force it.
     
  3. JSRP

    JSRP Senior Member Verified Member ECF Veteran

    Joined:
    May 1, 2014
    Location:
    London, United Kingdom, United Kingdom
    The cotton should be small enough so that you can pull the cotton back and forth without much resistance, but thick enough so that the inside area of the coil is always in contact with the cotton.

    The cotton will generally expand when saturated with e-liquid so that's why you don't want it too tight. However note that in the case of larger coils, the cotton may in fact 'sink' under the weight of the e-liquid (something to look out for)

    As for amount of cotton, I tend to get as much excess as I can in a Dripper without obstructing the airflow. In a tank based rebuildable (like aKayfun), I find that you just want just enough cotton excess so that the ends sit on the deck without being squished.

    Sorry for the essay, hope that helps somewhat! :)
     
  4. Marc411

    Marc411 Ultra Member Verified Member ECF Veteran

    Supporting member
    Joined:
    Mar 17, 2014
    Location:
    Windy City
    That looks like a KF or Russian deck. As long as you are not blocking the juice channels you should be fine. I add just to mine before putting on the chimney to see how it looks and to do a test burn. If it looks long or blocks the channel I give it a little hair cut.
     
  5. Crow2

    Crow2 Full Member

    Joined:
    Jun 12, 2014
    Location:
    Los Angeles, CA
    How about length?
    Assuming I'm using a dual micro coil, slanted up a little, I tend to cut it off right at the end of the coil on the outside end (closest to the cap), and leave just enough on the other side to come down and touch the well. Maybe a little extra to lay it flat. I like to change flavors frequently so this works for me, but I do need to drip more often.
     
  6. DavidOck

    DavidOck Vaping Master ECF Veteran

    Supporting member
    Joined:
    Jan 3, 2013
    Location:
    Eatonville WA
    You're building on a Kayfun type?

    I pull the cotton up through the tube of the chamber and cut it about 1/4" above that. Tuck down around the base with a toothpick.

    Amount... as said, just a slight resistance when pulling through the coil. Enough so you notice the drag, but not so much that you distort the coil.
     
  7. p7willm

    p7willm Super Member Verified Member ECF Veteran

    Joined:
    Apr 11, 2014
    Location:
    Lansdale, PA, USA
    One way to tell is to vape it. I have found that too little or too much cotton will give dry hits so, if you are getting good performance you have the right amount. Dry hits are probably too little to wick properly or too much and it is too tight to wick into the coil.
     
  8. ej1024

    ej1024 Senior Member ECF Veteran

    Joined:
    Mar 24, 2014
    Location:
    usa
    Everything that was said was correct,there's one more thing you have to know what kind of e-juice you are using,in my own vaping experience I use water based juice inside a kay fun to prevent burning and clogging ur coils,fruity,candy are the best juice in a kay fun,
    Just enough cotton not too much,if u put too much I'm 100% sure you will have leaking and clogging..thicker juice are highly recommended to be drip,if u want to use a thicker juice in a kay fun use a double barrel coil 2 28 g 10 wraps sitting side by side I do have this current built inside my tai fun gt and kay fun 26650


    Sent from my iPad using Tapatalk
     
  9. JustB'nMe

    JustB'nMe Super Member Verified Member ECF Veteran

    Joined:
    Oct 25, 2013
    Location:
    TX
    It's hard to judge the amount of cotton by a picture. To me, things tend to look bigger than they are in reality. So, although it looks like a lot it's probably just right.

    I use just enough cotton to touch and slide back and forth through my coil. My tails aren't quite as long as those pictured. I only allow mine to touch the top of the deck. Initially, it takes a bit of trial and error. There isn't one perfect way to build and wick except the one that works for you. Good luck!

    Live well, Love much, Laugh often and Vape on.
     
  10. Paradicio

    Paradicio Hazy Verified Member ECF Veteran

    Supporting member
    Joined:
    May 30, 2014
    Location:
    Altadena, CA
    Lots of great advice here, thank you all! :vapor:
     
Thread Status:
Not open for further replies.

Share This Page