Search results

  1. sparkky1

    Here I go again...

    Your going to have the erg but until you make the choice to reduce the risk, what may one day save your life or as I call it, better quality of life, keep doing both ............
  2. sparkky1

    Tf-r1,Tf-r2 what size Clapton wire would fit?

    What ohms / metal type where your quads and what watts / TC ? did you enjoy them @
  3. sparkky1

    No Sense of smell ... So need STRONG tasting liquid

    If your seeking a pre mix custard done right Royal Vape Custard E-Juice 7 great choices
  4. sparkky1

    Mod warm while charging.

    Have you concidered purchasing an external charger
  5. sparkky1

    Uwell Crown

    1/3 the price of what ? Stainless Steel Wire 316L
  6. sparkky1

    Uwell Crown

    Can be used for either, personally stainless 316L is my preference of choice in power mode
  7. sparkky1

    Uwell Crown

    Yes, just take it easy for the first 3/4 of the first tank, no long slow pulls, watch for air bubbles and should then be broke in good.
  8. sparkky1

    Best single coil RTA at the moment?

    Any build you can think of, Griffin 25mm
  9. sparkky1

    Uwell Crown

    Do you have a sweet candy / dessert flavor in it ?
  10. sparkky1

    Coil

    That's like saying, I don't like salt on my fries, so therefor it's better
  11. sparkky1

    Maximising battery life on my single 18650/smaller devices.

    Wouldn't it just be a little easier not having to work with 32 - 28g and worry about every second vaped, instead, just install another $5 battery ?
  12. sparkky1

    Maximising battery life on my single 18650/smaller devices.

    Amperage draw is determined ONLY by watts, nowhere is ohms law factored for max CDR through a PCB regulator, to get your "optimum" results for any given ohm / gauge coil, a seasoned builder would run the numbers for heat flux with watts applied to achieve this ..............
  13. sparkky1

    Question for those of you running a rx200 uwell crown combo..

    The problem is not with the watts but with the overly compressed cotton in the coils they've been putting out, a fix would be to penetrate 3 - 4 holes in top and sides with safety pin but still need to properly prime the coil and NOT start with long slow pulls, high watts with high vg
  14. sparkky1

    Question for those of you running a rx200 uwell crown combo..

    How are you priming a new coil and what watts do you start with
  15. sparkky1

    Get nic out of juice

    Not without buying the same flavor in 0 nic or diy flavors ......................
  16. sparkky1

    Your opinion

    GeekVape Griffin 22 RTA Innokin Cool Fire 4 PLUS iSub G Kit - Bold Vape Pico Starter Kit
  17. sparkky1

    Battery safety and high temperatures.

    Plastic 2 X 18650 Battery Case Type B - Batteries, Chargers, and PowerPax Carriers
  18. sparkky1

    juice travelling via cotton.

    That whole one side of the well with no coil should be empty of cotton, just drop the tails straight down and tuck directly under coil, maybe 1/4 in past the bottom and tuck, you want a nice gap in between coil and tucked cotton Cotton Bacon by Wick N Vape
  19. sparkky1

    Battery safety and high temperatures.

    This is pocket friendly Eleaf iStick Pico 75W TC Starter Kit by Jay Bo Designs
  20. sparkky1

    Are Vape Wild flavorings water soluble?

    Why not try a vendor that doesn't use an India based call / network center Maybe try "anyone" else ? Glazed Donuts by Loaded Night by Daily Dose E-Liquid 60mL Royal Vape Custard E-Juice 7 great choices Premium USA Made E-Liquid & E-juice, Manufactured in Tennessee at Mountain Oak Vapors
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu