Search results

  1. bapgood

    Just hemp

    I have had a few inquire about my hemp TGT build. So I finally remembered to take pictures this morning when I rewicked. I vary the number of stands depending on the air tube I'm using and my mood, but its usually 8-10 thru the coil and 18-20 total. This build was on my authentic TGT with 1.2mm...
  2. bapgood

    dna 30, dna 20, Groove, or zmax PCB board to make my mod?

    No they are selling the board for $65 and charger for $13
  3. bapgood

    Cardboard/fiberglass/carbon fiber DNA 6000mAh

    That is a 65-130 c-rated battery so it can handle 780 amps burst or 390 amps continuous. It has the lowest internal resistance of any battery I have tested. I'm not sure where you got the 1.2 ohms from unless it's actually milliohms, on my cheapo meter it tested between 6mΩ and 1mΩ or 0.006Ω and...
  4. bapgood

    dna 30, dna 20, Groove, or zmax PCB board to make my mod?

    Where did you get the DNA30 and what comes in the kit?
  5. bapgood

    my humble start

    lol....sounds like a bad day. But you never know with Evolv, they have over the top customer service. Shoot them an email and see what they say, the worst they can say is your SOL....which you were already planning on anyway.
  6. bapgood

    my humble start

    From what I can tell it looks aok to me. What's wrong with the DNA? Besides a broken screen?
  7. bapgood

    Battery Internal Resistance Measurements

    The higher the vaped at wattage the more load the battery will see and vdrop under load will be higher.
  8. bapgood

    My DNA20 box mod project build

    I will double check but I think it will work, but this would be cheaper if you had to buy something $2.31 Replacement Kick Tube for Chi You at FastTech - Worldwide Free Shipping
  9. bapgood

    Taifun GT Discusion!

    Are you in the correct thread? My TGT's don't have juice flow control, and have never seen one that did.
  10. bapgood

    The "WeekEnder"

    Nah....just less brains in the dome :D
  11. bapgood

    The "WeekEnder"

    Possibly :lol: I have very carefully ground just enough of the silver packaging away to expose enough of the tab to solder to :D However it should be said....safety safety safety....done at your own risk....etc....etc
  12. bapgood

    Battery Internal Resistance Measurements

    Just thinking you could run the VTC4 in the evic and see what your charger looks like after you have discharged the battery in the evic.
  13. bapgood

    The "WeekEnder"

    Hadn't seen that, that should work.
  14. bapgood

    The "WeekEnder"

    This is the only thing I have seen. https://www.fasttech.com/products/1411/10005381/1565103
  15. bapgood

    Battery Internal Resistance Measurements

    Phone Guy - do you still have the evic? One thing that shouldn't be over looked is the battery contacts, wiring, etc. These things can effect vdrop substantially. Also what is the voltage cutoff on the evic? It could be lower, and thus the difference your seeing on the charger. Most of these...
  16. bapgood

    The "WeekEnder"

    It probably should, I will see just turns bap turns out. I have to make it fairly large so hopefully it prints good, so after I see how it prints I will know better if I can get "Tibs by bap" to fit and print good. Just hate the waiting.
  17. bapgood

    my humble start

    No ideas unless you hooked the battery up backwards. I have never had a faulty board. edit - any pics?
  18. bapgood

    The "WeekEnder"

    Thanks asdaq!!! I probably went thru a good couple hundred fonts to find one that I liked.
  19. bapgood

    The "WeekEnder"

    Maxi :D
  20. bapgood

    The "WeekEnder"

    Then it will fit, with 0.45mm to spare :lol:
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu