Search results
-
Subtank RBA builds? show em!
No pic and the link goes to the Steam Engine calculator...sometimes ECF screws up pics.- Taowulf
- Post #284
- Forum: Coil Builds
-
SXmini M Class (TEMP CONTROL)
I compared it to the aluminum bottom of my silver IPV4, I expect to see wear marks on that, as the the protection is pretty minimal. The finish is so nice on the rest of the M Class, I was just disappointed to see paint wear already. Oh well, I guess this means I am breaking it in. :) -
What's the best vaping device out there so far?
This is the real deal right here. -
Do Not Buy The Istick 50W - My 3 month documentation
If you have a device that is not fully functioning and it is still within warranty, perhaps it is best to exchange it next time before further problems can develop. -
Portland Metro Area Vapers
Curse you Wetside Vapers. :) From the Dry Wastes of Oregon- Taowulf
- Post #14
- Forum: Oregon Trail Vapers
-
EFEST LUC V4 Issues
Another Luc4. Even though yours had issues, there is not a better charger unless you go to the high stuff some RC guys use.- Taowulf
- Post #2
- Forum: Batteries and Chargers
-
Do Not Buy The Istick 50W - My 3 month documentation
Malfunction in week 3? Did you buy it from a 3rd party vendor and have no warranty? -
IPV4 preorder
I think you missed a zero there. The IPV4 goes down to .05 on Nickel coils in TC mode. Edited to add - I've seen spec sheets that say .12ohm to 1ohm...but since when does P4Y know what they are doing? LOL Frankly, I don't want to see a 1ohm nickel coil, that thing would be HUGE. -
SXmini M Class (TEMP CONTROL)
I am just a little dismayed it started less than 7 days after I unboxed it. After a month or two? Ok, I can see that. And it doesn't even sit directly on the desk most of the time, it sits on one of my many Bad Drip microfiber coasters a lot of the time. The silicon condoms are hideous. As... -
SXmini M Class (TEMP CONTROL)
I've had my Mini M class for 7 days...and already the paint is wearing off of the base. Already emailed Yihi about it. -
flat top or button top for sx mini?
over 31000j with Samsung 25Rs, go with flattop. -
Temp Control
You can always top fill the orchid by removing the top, covering the air holes with your fingers and fill it that way...juice loss is minimal. Just have to blow it out a little into a towel or napkin. As far as the OP's question goes, I have gone with the Lemo, Lemo 2 and Subtank plus for temp... -
-
-
Core-"In" Clapton Build
Wait, you were removing the core of a Clapton? There was no reason to do that in the first place....just sayin.- Taowulf
- Post #4
- Forum: Coil Builds
-
The Billow v2!
Bulbous? It is barely a 1mm increase! That is sexy right there... -
NICKEL WIRE
I support what Dr F has done, but I am pretty skeptical of his grasp of metallurgy. I am done with torching wires. I've found that gently strumming the coil while heating it (way below glowing) is sufficient to get rid of hot legs. That is for Nickel coils. the technique works even better on...- Taowulf
- Post #31
- Forum: General Vaping Discussion
-
The Billow v2!
I was refilling yesterday and the chamber decided to stay in the tank, so you can see the wicks a bit here... I sent a Billow V2 to a friend and he said that the wicks are too short. Nope, they are just right. -
SXmini M Class (TEMP CONTROL)
I hate the removing the battery twice a day, so charging it occasionally via USB is better than cursing while I unscrew the battery. :) -
SXmini M Class (TEMP CONTROL)
Join your voice to mine in requesting a visible charge indicator on the M Class that is more than the little symbol on the battery indicator. If you use the USB charge at all, it is an essential indicator. I would like to see a progress indicator and a "charge complete" indication. You shouldn't...