Search results

  1. PKZap27

    Scubagen Mods

    Thank you Dan! I'll wait for the video. However, if it makes it easier for you, can you fileshare the video like the instructions.
  2. PKZap27

    Scubagen Mods

    McMaster-Carr sells them. M1.6 Hex Nut - Part Number: 91828A006
  3. PKZap27

    Scubagen Mods

    No! The nails are steel. You couldn't solder to them if they were SS.
  4. PKZap27

    Dear Gummy.....

    Happy Birthday Gummy Bear!
  5. PKZap27

    Scubagen Mods

    About the picture showing condensate in the lower tank... It may have been juice that ended up getting inside the tank too, or both.
  6. PKZap27

    Scubagen Mods

    Thank you bmwzero! Yeah! That's it... During this part of the build the tank is empty. The air inside the tank was heated while heating the wick and when the air in the tank cooled the moisture dropped out of the air causing the condensation. The humidity is high today and I set...
  7. PKZap27

    Scubagen Mods

    Kanthal 32, 3 Wraps, 1.7 Ohms. I push the button on my 650mah ego battery and within 2 seconds this is what my coil looks like. The wick is dry and the tank is empty.
  8. PKZap27

    Fender0942 & bstedh's Scubagenv3 CO-OP discussion

    Yeah, I guess that was more of a storage solution vs. a working solution.
  9. PKZap27

    Scubagen Mods

    This will keep the Kanthal from unraveling on the spool. Take a pair of side cutters and cut two notches in the outer lip of the spool. I used a pair of cuticle cutters to cut my notches.
  10. PKZap27

    Fender0942 & bstedh's Scubagenv3 CO-OP discussion

    Take a pair of side cutters and cut two notches in the outer lip of the spool. I used a pair of cuticle cutters to cut my notches.
  11. PKZap27

    Scubagen Mods

    Are you boiling you mesh like Raidy said for at least 5 minutes. Just checking to see if this is a reason. I didn't boil my last wick. However, I did boil the previous one and it didn't seem to matter. I think when you quench it. It is pretty much clean after that. not unless...
  12. PKZap27

    Scubagen Mods

    Yes, vape through... meaning break in. doing less wraps setup now My all time Vape... DIY 36mg, 80/20-PG/VG, 6% WB peppermint from TPA. 6 drops TPA WB Sweetner per 30ml. I vaped straight PG in the scubagen... to see if my 36mg high nic juice was causing the TH issue. I...
  13. PKZap27

    Scubagen Mods

    I use the higher nic to keep me from chain vaping. I don't have to hit my PV too much with the 36mg, I like it that way. I hit it a few times every 15 ~ 30 minutes. some times longer. I'm good.
  14. PKZap27

    Scubagen Mods

    Maybe I need to vape through it at the higher voltage...
  15. PKZap27

    Scubagen Mods

    It's water based peppermint I even vaped plain PG in it to see what it was like. Plain PG on ego TH = 20 Vapor = 5 Flavor = It's PG:
  16. PKZap27

    Scubagen Mods

    I'm not sure what your mean.... I tried the genisis atty at higher voltages. it didn't get any better.
  17. PKZap27

    Scubagen Mods

    Funny you say this about switching the mesh. I'm switching from the #400 to see what the 325 is like.. or what ever my other sheet is that I recieved free from the Mesh Co. Also switching mesh to make sure I didn't think one was the other. --------------------------------------------...
  18. PKZap27

    Scubagen Mods

    I'm re-wraping mine right now to go to a lower Ohm. I had 2.5 Ohm for 5 wraps... so it is about 0.5 ohms per wrap. I'm trying three wraps now. shootin for ~1.5+ ohms.
  19. PKZap27

    Scubagen Mods

    I don't know. However, I just bought the ruby flux, because I didn't want to run into complications... For my first build, I figured I would build it just like Dan. Doing it this way weeds out all the variables if I were to have any issues. Once I get my first build done. And I know...
  20. PKZap27

    Scubagen Mods

    Like in Dan's tutorial... Using the parts and the materials that he has listed for this Co-Op.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu