Search results

  1. HazMatt

    anyone using twisted wire?

    I have not tried it yet. Because, I don't have a drill...I know I am risking my Man card by admitting that ;-) Several months ago I ordered 100 ft of 32g kanthal A1 from Temco. I recieved 200 ft and an additional 100 ft of 32g nichrome. I will definitely be twisting some 32g in the near future.
  2. HazMatt

    Russian 91% v2 irratic resistance readings

    Thank you.
  3. HazMatt

    Russian 91% v2 irratic resistance readings

    Please post or send me the link to their Facebook page. I cannot find it.
  4. HazMatt

    Russian 91% v2 irratic resistance readings

    They probably sold out. After you finish shoveling all the manure out of a truck, you don't want to leave any trace of it behind.
  5. HazMatt

    Russian weeping/leaking? (Last whiny post i promise lol)

    Don't buy the Russian 91% V2 just yet. Some of us R91 V2 owners are having problems with the floating positive pin/airflow tube. We are getting ohm readings that erratically jump around. Also, even after tightening the center tube/pin down very tightly, the positive block twists out of...
  6. HazMatt

    The gap between air hole under the coil and the coil assembly very important (Kayfun) >

    Now that I have been using my R91 v2 for a couple days, I agree that they are a superior vape. However, I work in an industrial setting and I will still be using my ego/mini protank 2 setup while at work. I would hate myself if I lost or broke such an expensive piece of gear.
  7. HazMatt

    Russian 91% v2 irratic resistance readings

    Finally, I am vaping my R91% V2. My current coil is at 1.7ohm and holding steady on my SiD. After only a few draws, I can see that 18mg is way too strong. The flavor is great, just a hair off from dripping. Vapor production is good though, not as thick as I had hoped. That may be due to the...
  8. HazMatt

    Russian 91% v2 irratic resistance readings

    Same vendor here
  9. HazMatt

    Russian 91% v2 irratic resistance readings

    I contacted my vendor and they also said that the V1 center tube can be used. If you don't have a V1 center tube, they suggest screwing the atty onto your device. Then, unscrew the atty 1/8 turn, then tighten it down again. They said that this seems to allow the spring to reset giving a...
  10. HazMatt

    Russian 91% v2 irratic resistance readings

    I agree. If I had know about these problems, I would have bought a V1 from the classifieds.
  11. HazMatt

    Russian 91% v2 irratic resistance readings

    @ SilverZero I also noticed that I could screw the base completely snug against everything i tried it on. Vamo, SiD, and Lil black box ohm meter.
  12. HazMatt

    Russian 91% v2 irratic resistance readings

    I did that also. I could not tighten the center pin enough, with hand strength alone. So, I grabbed another pair of pliers and used them to hold the spanner wrench. I was able to get about an extra half turn, on the center pin, before it felt truly snug. Even after that, the positive block...
  13. HazMatt

    Russian 91% v2 irratic resistance readings

    After some rest, my coordination has returned. I was able to tighten the center pin. So much, in fact, that I bent the forks of the spanner wrench. A lot of (expletive) good that did. After installing a few coils, the positive block has started turning again, when tightening the positive...
  14. HazMatt

    Russian 91% v2 irratic resistance readings

    Yep, same (expletive delete) problems. Since I had a pre-wrapped coil in my tackle, make that vapor box, I decided to install it in the R91 v2 that arrived today. First, I try to loosen the positive terminal only to discover that apparently, I must finish ASSembling this piece of (expletive...
  15. HazMatt

    Russian 91% v2 irratic resistance readings

    considering I am about to wrap up a 16 hour shift, I may not get around to cleaning and building it until ttomorrow night. But, I will report what I find.
  16. HazMatt

    Russian 91% v2 irratic resistance readings

    Not what I want to hear. I ordered my first Kayfun style atty, which happens to be a R91 v2. It should be in the mailbox waiting on me when i get off of work tonight.
  17. HazMatt

    Is this normal?

    I use 18mg in my Protanks, 12mg when dripping on a single coil around 1.0 - 1.6 ohms, and 8mg when sub ohm dripping. I need some 4mg for the rare times I build .5 ohm or lower coils.
  18. HazMatt

    Kanger - Ignoring replacement coil insulator market

    I might even be willing to pay $5 for 20. A quarter each for smaller amounts doesn't sound horrible.
  19. HazMatt

    The gap between air hole under the coil and the coil assembly very important (Kayfun) >

    My very first Kayfun ( actually a R91%) is on it's way from Washington state. This is my most anticipated vape mail yet. That is a nice compact setup you have there. Here is a pic of my mini protank 2 on a 400mAh vision micro ego. Between a 10ml bottle from Juice Mafia and a 15ml bottle...
  20. HazMatt

    Russian 91% vs Cheaper Clones

    I wish I could find a MVP V1. Or, was it 1.5? VV only, no ohm checker. The last vape meet I went to, a vendor had dozens of them, trying to sell them off since the V2 had just released. Maybe I will get lucky and he will be at the next meet on the 6th.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu