Search results

  1. drmarble

    Printed Mechanical Bottom Feeder Mod

    I think the fasttech one is the same. The photographer just put the vented screw into the center post. The center post does have drain holes like the original, they are just facing the negative poles. I found this out from reading the comments and reviews. I was only suggesting drilling if the...
  2. drmarble

    Printed Mechanical Bottom Feeder Mod

    You can get the zenith 2.5 bottom feeder for under $10 here: https://www.fasttech.com/products/1901902 Fasttech's shipping is slow (2 weeks from China) but it should get to you faster than your shapeways/sculpteo parts. I figured I could just drill another hole at the base to avoid leaking if...
  3. drmarble

    5 pin duel led switch question

    It might have a built in resistor. Use your multimeter and check resistances between the terminals. You could also look at the data sheet and see if it shows a resistor. If is is specified for 12V it probably does have a resistor built in in which case you will just have a dim led. If it had no...
  4. drmarble

    Building a "hana" style mod with the fasttech enclosure: looking for tips, tricks, and suggestions

    My boxes, ordered from elev8 on the 25th, just appeared in BETHPAGE, NY 11714. Maybe they will get here eventually. Did everyone else's also end up there? Or did they take tours to different towns. Looking forward to modifying them. I figure one bottom feeder and one with a vamo chip. Probably...
  5. drmarble

    Is Genny still alive?

    Get a kraken (or a clone) They are great gennys. I admit I cheat and wick with rayon or cotton.
  6. drmarble

    Official DNA 40 introduction

    rossum found some titanium on amazon. I believe they have 30 and 26 gauge. There is also a European supplier with other sizes and purities.
  7. drmarble

    Focalecig ... A new Fasttech??

    Black friday sale here: BlackFriday Some items look pretty tempting.
  8. drmarble

    Official DNA 40 introduction

    With a diode having a 0.7 volt drop if you are drawing 20amps you dissipate 14 watts in the diode while firing. This would require a large, heat sunk diode. It would also greatly decrease battery life. They could have installed some fuses. They would work much better. Mamu has some excellent...
  9. drmarble

    VaporShark rDNA

    Upgrade to the '40 chip. It has reverse battery protection and thus is safe from you tender ministrations while installing batteries. It Should give a much better vape than an istick. You don't have to use the temperature protection/nickle wire. $ is a great deal for an rDNA40 even without...
  10. drmarble

    Focalecig ... A new Fasttech??

    I am very attracted to: $12.43 Vaping Coil Winding Jig Tool for Rebuildable Atomizers - Silver I don't really need a coiling jig; I use one I built. I just think the pictures make it look very good. I don't know how to show images here. I'll try a couple of links...
  11. drmarble

    Building a "hana" style mod with the fasttech enclosure: looking for tips, tricks, and suggestions

    Often you can tell that it is fully mixed because the resin and hardener are different colors. When the mix is a uniform color it is ready to be applied with the toothpick. The cardboard and toothpick is the recommended method.
  12. drmarble

    Where to get the old 1A micro usb charger?

    Is this the one you want. 5V Micro USB 1A 18650 Lithium Battery Charging Board Charger Module Protection | eBay It is 27 * 18 * 10MM vs. 25X19X10mm. Hope this helps.
  13. drmarble

    Official DNA 40 introduction

    I think this is the cheapest from a very reputable manufacturer with product that ships quickly: XPV DNA-40D with Temperature Protection | Protovapor.com If vapedojo has any bap 40's left you could look at them bapgood makes nice dual 18650 mods.
  14. drmarble

    My thoughts and issues with the DNA40

    Mamu has some good suggestions for a similar build here: http://www.e-cigarette-forum.com/forum/battery-mods/538730-arlo-dual-18650-dna20-30-step-step-how.html Hope this helps.
  15. drmarble

    Printed Mechanical Bottom Feeder Mod

    You can go here: http://www.e-cigarette-forum.com/forum/announcements-news/283955-how-become-verified-member.html to get information about getting verified. I understand that there are some delays in verification now do to personal problems befalling the administrator. Be patient. There is a...
  16. drmarble

    Taifun GT Discusion!

    They are gone from Focalecig now. They even had a no logo version. Maybe it is under a different name now. I am also curious about the airflow versions. I can only reorder type B myself. Let's hope that no-logo versions appear soon.
  17. drmarble

    Taifun GT Discusion!

    All the taifuns are gone from fasttech. I assume there has been another copyright infringement suit. Even the SS tank (with logo) is gone. I hope that logoless ones come out soon. I almost ordered another one last night but decided to first try out the Erlkoenigen clone that is coming soon...
  18. drmarble

    The Erlkönigin : PICTORIAL

    fasttech has them: $1.79 Rotatable Round Mouth Electronic Cigarette Cartridge Adapter Drip Tip - silver / aluminum alloy + plastic at FastTech - Worldwide Free Shipping Different colors are available. Cheap ($1.79).
  19. drmarble

    Best place to buy kanthal wire?

    lightning vapes. Sells on amozon or their own website. LV15 coupon code gets 15% off so the website prices match their amazon prices. I've been using them.
  20. drmarble

    Focalecig ... A new Fasttech??

    The manufacturer sells a threaded adapter that lets you use any drip tip with the erlkoenigen. FT sells one clone that comes with an adapter: $15.75 Erlkonigin Style Rebuildable Tank Atomizer (8ml) - stainless steel + PMMA tank / 20.7mm dia. at FastTech - Worldwide Free Shipping Hope this helps.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu