Search results

  1. T

    HOHM Wrecker 151W TC ?

    a little?
  2. T

    HOHM Wrecker 151W TC ?

    Well said.
  3. T

    Evolv-ing Thread

    Unless that .6v is reading resistance, I wouldn't expect the the DNA to pass it to the positive lead, especially in sleep or OFF mode.
  4. T

    Evolv-ing Thread

    Didn't you say you propped the fire button using resistance wire to hold something to the board? Any chance that may be touching something it shouldn't?
  5. T

    Evolv-ing Thread

    The DNA is passing .6v into to the positive lead to the 510?
  6. T

    Evolv-ing Thread

    Steamer, You are somehow bleeding voltage constantly without use and since you swapped a DNA in the only thing you probably saved from the original setup was the sled and its wiring. Sounds like a voltage leakage in the battery sled/leads due to poor insulation. Look for an exposed wire or...
  7. T

    Evolv-ing Thread

  8. T

    Cupti By Kangertech

    I have 2 and have had mixed success. my first build, a Ti coil, I wicked as I normally would have & it wicked ok and performed well through a few refills. My second was ss316 where I trimmed off the wick tails & thinned tthem before inserting to wells. That build provided burnt hits under TC...
  9. T

    Evolv-ing Thread

    Too Far? Kind of a testament to the change of season.
  10. T

    Evolv-ing Thread

    Perhaps that was my mistake, or the FT SMY clone was more restrictive. When I get some time, I'll play with them a bit more.
  11. T

    Evolv-ing Thread

  12. T

    Cupti By Kangertech

    Not a rookie mistake as both methods are acceptable, but it can restrict as the cotton compresses at the wicking hole. After you pull cotton thorough, trim close to coil body & gently push the dry cotton back through the hole so it is pushing against the inside of coil body and blocking hole...
  13. T

    Cupti By Kangertech

    Are you tucking the cotton back into the juice hole so it remains inside the coil body or are you leaving it to protrude. Leaving it to protrude can cause issues restricting flow of juice. If you are tucking it back in, I'm at a loss as to what else you can try other than to try to spread the...
  14. T

    Evolv-ing Thread

    Notch is a lot better on the DNA after Evolv redid the curve. Before that I used to set a TCR Linear curve for them on the DNA, forget the number, maybe .00125 or something like that. Found it somewhere in the Cubis thread and it ran good with it. The Stock 0.25ohm Vertical Notch coils for...
  15. T

    Evolv-ing Thread

    I liked Lemo 2 and used them regularly for single Ti coil builds. Tried KF5 but much too restrictive for my taste. Lately I have been lazy and have just been using some Cubis tanks I bought dirt cheap a while back with 0.25ohm notch coils. Just been too busy to build and those crappy little...
  16. T

    Evolv-ing Thread

    The older Lemo 2 wasn't a bad single coil atty for its day. Had good air & good flavor at the time, but tried going back to it after Aromamizer and it felt pretty restricted. Gotta have more air than a KF though.
  17. T

    Cupti By Kangertech

    How you rebuilding it? Horizontal coil wicked straight through the holes? Cotton may be too dense.
  18. T

    Evolv-ing Thread

  19. T

    listing side by side mods

    Received a White 40w & Blue 70w Tesla Stealths today from VaporBeast. Haven't opened the 40w yet. I ordered them without the tanks. The 70w is a bit taller (1/2") & heavier than Knight V2. Tesla seems to fire slightly faster on a button press than the Knight on identical attys, but seems to...
  20. T

    Evolv-ing Thread

    Was anyone lucky enough to take advantage of the YetiVape Black Friday Deal on Aromamizer Supreme? Just heard they were selling them for $3.75 ea. from a guy who ordered 20 of them. How did I miss that one? Edit: This apparently had something to do with a 50% off coupon combined with a...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu