Search results

  1. steved5600

    Screw on CLT RDA backing out?

    May need to torque it a little bit tighter. One thing you can do if it will fit is to put a spring on the screw to hold it. Don't have a CLT but things like clicking pen springs may work depending on the size of the screw. Will have to clip some of the spring off.
  2. steved5600

    Drilling out areotank airflow

    I have drilled out the ones with the treads. The one with out the threads does not need it as you are limited by the hole on the head.
  3. steved5600

    Need help from our veteran vapers.

    Thing about smoking is you can't force feed it. IMO it's a bit like alcoholism they aren't going to stop until they decide to. I'd show and talk about how good you feel how it's going etc. Good idea to have an inexpensive loaner for them to try an Igo starter kit would be my choice for a loaner.
  4. steved5600

    Some questions.

    Ok on those do dual coils Inside diameter 2-2.5mm you need some 28 ga wire. Dual 7/6 or 6/5 turns with a tight fit one coil next to the other. If you use 26 ga you will get a .4 ohm build. Use organic cotton. Do a test with out wick to see they heat at the same time and from the middle out...
  5. steved5600

    Ehpro kayfun lite + v2 issues

    The hole in the center pin does not have to line up with the air hole in the base. There is a big chamber in there. If you know someone with a drill press you can drill it out. Just make sure it's in a vice when you do it and if possible us a cobalt bit. If you dont use a vice and a drill...
  6. steved5600

    Life is in danger!

    Stop filling over the bed and don't lay them on it. Try presoaking them and wash with something like oxyclean. Make sure to scrub it good before you toss it in the wash and check to see if it came out before you toss it into the dryer.
  7. steved5600

    Can't advance past old tech, Joyetech cylinder attie and cart

    You do not want to go from a carto to rebuildables. Consider going to either a Glass evod dual coil or after we see some reviews the Nautilus mine with the Bottom feed vertical coil. This is a single coil system a lot like the cartos. But i'd wait and see on it. If you go dual coils you may...
  8. steved5600

    SVD Button issues

    The SVD has been plagued with button problems. Know two folks that the buttons just fell off making them hard to use.
  9. steved5600

    Will a single coil Evod head fit the new glass Evod?

    No they won't the heads look a lot a like but the BDC heads are taller to accommodate two wicks so if you try to put the BCC old Protank 2 heads in the new glass evods your juice will leak out and you will be sucking juice. Oh the threads are the same just the top part of the heads, insulators...
  10. steved5600

    Rosewill 6.56ft. USB2.0 A Male to Micro USB Cable $.99 free shipping

    Spam spam spam
  11. steved5600

    26650 mods

    Copper Hades will hit hard. Have two. Got one on fasttech one more expensive one from another site and they both are great. I would NOT get the Stingray 26650 heard about problems with the switches.
  12. steved5600

    New member, new vaper...please don't read me the riot act for starting out sub-ohm vaping!

    Oh the reason folks get read the riot act noob or not is because if you screw up you an have a bad day. Bad day being a burn or worse. Am glad your asking but if your not using a battery like i listed above then consider this the riot act.
  13. steved5600

    New member, new vaper...please don't read me the riot act for starting out sub-ohm vaping!

    Unless your using a 30 amp battery like the sony vtc4 or vtc5 your gonna vent a battery. Your at almost 25 amps. Use this site to help you with builds. Ohm's law | Steam Engine | free vaping calculators
  14. steved5600

    Question about Aerotank Mega capacity

    Yes you can unfortunately you really won't know your out until you get a dry hit unless you keep tipping it on its side to see if there is juice. I have the mega and giant. Both have that problem. Shame they did not put a fill hole in the top could have gotten in at least another ml.
  15. steved5600

    .12 ohms?

    Quick answer No. Now for my speech i promised someone i'd give in these kinds of questions. You need to learn ohms laws, have an ohm meter and practice battery safety. Here is a site to help you with two of the above. Ohm's law | Steam Engine | free vaping calculators Hope this helps. Take...
  16. steved5600

    Tugboat or Tobh v2.5?

    I don't have the Tub boat but do have a tobh. The 3 post Tobh: Pros: easy to build Nice big post holes. Larger area for the wick and juice. Great air flow. All the posts are rock solid. Adjustable copper center pin. cons: I don't like the fins and wish the top were more of a tapered shape...
  17. steved5600

    Fasttech

    With FT it's hard to tell. I shop them a lot. Some stuff comes in 2-3 weeks some take longer. You have to check your messages on FT. AFTER you order you may get a message that says it's on Back order which will add to the time. My record so far has been almost a month. BUT I have had...
  18. steved5600

    Questions about watts/volts/resistance.

    Ok Volts = electronic pressure just like with water Lb's per sq inch. Amps is the flow as in gallons per hour with water. Resitance is just that anything that pinches off the current flow. Watts are a factor of volts, amps and resistance. Here is a useful site. Ohm's law | Steam...
  19. steved5600

    Paranoid: Is copper contacts/copper in general a safe material for vaping?

    Would not want it inside my atty's because it is reactive but don't know about toxic. My choice. SS and glass for me. Unless it's crappy copper and has zink in it can't see it being dangerous. That is bad. Copper contacts are not a problem. You are around them all day. Your not vaping...
  20. steved5600

    24g kanthal - problems 28g- seems perfect?

    Shortest possible legs on the coils. 2-2.5mm ID tight coils and make sure you got the best battery you got in it. Check to see they heat from the center. You did not mention the mech your using. A good copper mech will help a little. To many turns will slow it down. I can't imagine going...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu