Search results

  1. Wingsfan0310

    Hcigar VT133 -- dual battery

    Vape Mail Day! The set is finally complete. :) She's a Rainbow Cheers, Steve
  2. Wingsfan0310

    HCIGAR VT75

    Yes. Evolv uses a very good charging board. Cheers, Steve
  3. Wingsfan0310

    Lost Vape Therion DNA75 dual 18650

    The first time I set them up. I went to the material tab of Escribe. Click on import material (navigate to where you saved the CSV file and click on it), move that material to the box on the right (via the green arrow between the boxes - it comes on once you click on the material). Then set up...
  4. Wingsfan0310

    Lost Vape Therion DNA75 dual 18650

    I was just going to suggest that. They have some pretty nice custom screens for each profile as well. You will like them. Just load them 1 at a time. Example - Click on profile 1 then load profile. Then profile 2, etc. Put them on in any order you prefer. Cheers, Steve
  5. Wingsfan0310

    Lost Vape Therion DNA75 dual 18650

    You can't upload csv files here. I'd have to change them to .txt files.
  6. Wingsfan0310

    Lost Vape Therion DNA75 dual 18650

    I believe the Escribe presets are from Steam Engine. I get all my CSV files from there. I've saved 7 different TC profiles and 1 power mode (Put them all in a folder). When I get a new DNA, I just load them up. The profiles are as follows: Profile 1. Power Mode Profile 2. SS430 Profile 3...
  7. Wingsfan0310

    Evolv DNA 75

    I have a Lavabox M DNA75. I use Samsung 25R's in it. I have my cutoff set to 2.75v and can drain it until the battery bar is empty without getting the flashing bar. Since the mod you have is a single cell mod, you want to use at least a 20 amp CDR 18650. I have LG HG2's, Samsung 30Q's and...
  8. Wingsfan0310

    Evolv DNA 75

    Not on the DNA75 it isn't. That was the cutoff for the DNA200's using a Lipo. Since the DNA75 is a single battery mod, you will get more sag under load. If you set it that high you will get the low battery warning to quick. Manufacturers test 18650's down to 2.5v so there is absolutely nothing...
  9. Wingsfan0310

    Evolv DNA 75

    Make sure you have the newest version of Escribe and firmware installed (V 1.2 SP3). Set the cutoff to 2.75v. If that problem continues, get a better battery. I'm in a hurry so I made it short and to the point. Cheers, Steve
  10. Wingsfan0310

    Evolv DNA 75

    Hook your mod up to Escribe and look in the mod tab (battery section)
  11. Wingsfan0310

    TC beyond Ni200: Nickel Purity, Dicodes; Ti, SS, Resistherm NiFe30; Coefficient of Resistance

    Hi Steve, I'm using a couple brands atm. I really like the Lightning Vapes 28ss, 36ss(ga) a friend sent me to try. I'm also using MKWS (26, 32 and 28, 32ga) Clapton wire I bought from FastTech. I like them both but the 28ss,36ss LV wire is easier on the batteries ;) Clapton Wire $3.69 Authentic...
  12. Wingsfan0310

    HCIGAR VT75

    I'll add to what @TrollDragon said. It really depends on your vaping habits, coils you are running, power to get them up to temp, etc. I'll give you an example of what I'm saying: The same VT133, same batteries, approximately the same amount of juice used can last me a little over 1 day to...
  13. Wingsfan0310

    Evolv DNA 75

    I've heard of that happening to a couple of people. I think it sorted itself out though. I just want to make sure you are using the newest version. Evolv released one on 8-5, then another one 3 days later (8-8) to fix a few bugs, The 8-8 is V1.2 SP3. I think it will be alright after a cycle (or...
  14. Wingsfan0310

    TC beyond Ni200: Nickel Purity, Dicodes; Ti, SS, Resistherm NiFe30; Coefficient of Resistance

    When I was experimenting with the 25ga CW SS430 I was going between .00175-.002 At .002 it seemed over done. I was comparing it to the same settings I'm using on Unkamen SS430. I had both of them on different Supremes. The only differences were wire gauge (Unk 28 - CW 25ga) and TCR setting of...
  15. Wingsfan0310

    Evolv DNA 75

    IIRC On one of my VT133's I just removed the batteries for about a minute and that did the trick (while it was not plugged in). For a Soft Reboot: Tools > Diagnostics > Reboot Device > Soft Reboot Cheers, Steve
  16. Wingsfan0310

    Triade DNA200 by lost vape

    I'm using the Escribe and Firmware that came out on 8-8 (V 1.2 SP3) on my DNA200 mods. It's really smoothed out TC for SS316. I really like it. [EARLY] *** 2016-08-08 EScribe 1.2 SP3 *** https://downloads.evolvapor.com/SetupES250.exe (57MB standardalone installer) Cheers, Steve
  17. Wingsfan0310

    Triade DNA200 by lost vape

    What's supposed to happen is when a firmware is recommended, it's automatically downloaded to Escribe. When you want to be an early adopter, you need to download the Escribe that has it. I always switch to the new firmware as soon as it comes out so I just download and install the new Escribe...
  18. Wingsfan0310

    Hcigar VT133 -- dual battery

    They are all already gone. I had to grab one more so I had a mod for each color of battery cover I have. A 6 pack just sounds right! :D:lol: Cheers, Steve
  19. Wingsfan0310

    HCIGAR VT75

    There great mods. Here my chance to show off :lol: L to R DNA200 Lavabox, M DNA75 Lavabox Cheers, Steve
  20. Wingsfan0310

    HCIGAR VT75

    You have to check out the Blood Red Lavabox M DNA75 then. I think you will want one if you look! Edit That makes me sound like an enabler :lol: Cheers, Steve
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu