Search results

  1. S

    How to get more Vapour out of the Kanger T3

    That's fair. Honestly, my problem with the T3 has always been mainly about the flavor production, which is good but not great. The OP wasn't asking about flavor, but about vapor, so my impressions may not be the most useful, as my goals are different. I vapor production isn't terribly important...
  2. S

    How to get more Vapour out of the Kanger T3

    You are entirely right. I should have said "A higher resistance head with a smaller ohm number uses smaller wire in the atomizer. Since the wire is smaller, the same amount of voltage makes it hotter." I still get hung up on a lower number indicating higher resistance sometimes. How...
  3. S

    Is there a tank system that does not need wicking??? Just a coil and tank ?

    Turns out there's a reason for that. I pulled all the bridging and wicking out of a couple of my Cisco LR 306s and... They don't work very well. They just don't retain fluid, for obvious reasons. Now, maybe with a bottom feeder...
  4. S

    How to get more Vapour out of the Kanger T3

    Kanger T3s are simple and fairly reliable, but they're only ok for vapor production. The tight wicks simply don't bring juice in quickly enough to have a lot of juice available to vaporize. That said, you can raise your wattage, which will raise your temperature. To up your wattage, you can...
  5. S

    Interested in a San Francisco Bay Area vaping event?

    I'm thinking about putting one together. Interest / planning thread here: http://www.e-cigarette-forum.com/forum/general-e-smoking-discussion/398896-possible-event-vapemeet-san-francisco-bay-area-interested.html#post9102558
  6. S

    Possible event: VapeMeet San Francisco Bay Area - Interested?

    It feels like vaping is finally taking off in San Francisco! Who'd be interested in a vapemeet? I've been talking to a few friends and a couple vendors, and we're thinking about putting one on. Three questions for you: Would you be interested in attending a vaping event in San Francisco...
  7. S

    Vapor City on Polk St in SF

    I stopped by the other day. Here's their Facebook page: https://www.facebook.com/pages/Vapor-City/570804859604669 They're at: 1347 Polk Street, San Francisco, CA 94109 Cross street is Sutter Hours are every day, 11am-6pm. They also just put up their website: Welcome to Vapor City...
  8. S

    Vapor City on Polk St in SF

    I didn't know there was a new shop in SF! What's the cross street? I can't find any info on it online.
  9. S

    **IKV Update**

    Are any of the unpunched and unflanged cartos available now XL size? I can't really tell on the site. I'd love to get some for my Jazz Cartopipe, but it only takes XL length cartos with no flange, and of course a punched carto would leak.
  10. S

    Why does the Provari hit differently than the eVic?

    Everyone said that the Provari hits better than the eVic, but I couldn't imagine it was true. It's just delivering voltage, and I wasn't gonna go past 5V anyway. So I ordered the eVic. And it was good. Then I got a Provari. What can I say? Subjectively, the Provari does seem to vape better...
  11. S

    Supporting Member Giveaway - Master Artisan's DIY Kit from One Stop DIY SHop

    What a great contest, and great timing! I just started getting into DIY, but have been using a friend's supplies.
  12. S

    What brand RY4 has the house logo?

    That's the stuff! Thanks so much.
  13. S

    What brand RY4 has the house logo?

    My favorite RY4 so far is the plastic bottle with the white label and the little log cabin logo. Anyone know who makes it? I've been buying from my local B&M but they're out of 12mg.
  14. S

    New Hybrid: The Noble1 from Vapor Craze

    Still absolutely loving it. I actually went back and bought a second one! Here it is full of Pluid and with a more reasonable tip.
  15. S

    What do you use to vape Pluid?

    Thanks for the advice! I managed to track down a hybrid at a launch event down here in LA and was even fortunate enough to have an experienced vaper show me how to set it up. I'm vaping Pluid from it now, and I've gotta say, this thing kicks. No comparison to the clearos and carto tanks I'd...
  16. S

    New Hybrid: The Noble1 from Vapor Craze

    I hadn't seen this mentioned yet, so I thought I'd share. I went in to Vapor Craze / 310 Vapors today hoping to see a hybrid in person and learn a bit about them. Lucky for me, it turns out they were releasing a new one tonight! I just got back from the event with my new baby. It is a...
  17. S

    List of Hybrids?

    Don't forget the Noble1, just released today by Vapor Craze.
  18. S

    eVic 1.2: Changing wattage changes voltage?

    Huh! So rather than just controlling something that influences the amount of energy going to the coil you're controlling the quantity of energy more directly, with the mod doing the math? That is pretty cool! I take it this would correct for switching between different resistance attys? Is...
  19. S

    eVic 1.2: Changing wattage changes voltage?

    On my eVic running firmware 1.2 in VW mode changing the wattage makes the voltage change, and changing the voltage makes the wattage change. You can see this by holding the wheel "left" until it cycles to the screen that displays ohms and volts in little letters (while it VW mode) or ohms and...
  20. S

    What do you use to vape Pluid?

    Thanks for all the great advice! What sort of device would I want to run a SLR coil? I also tracked down the video you mentioned. This one, right? zenesis coil basics - YouTube
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu