Search results

This is supposed to stop the charging when its running the test. But it gives small amounts of charge and the case slowly heats up when its supposed to be cooling. Any ideas? This is my first dna mod. Attached is pic.

Where can I find this stuff from a reputable vendor?

Every device I own does this and it has to be some error im making across all my different devices when I try temp control. I have my mod set to 580 and it ramps up very rapidly to max and stops making vapor. This mod (espion) with a red panda firmware is supposed to be good at tc and it does...

I am new to TC vaping. I saw on djlsbvapes that he shows what a particular TCR value reads at temperature wise for a lot of mods. My question is how could I do this on my own? I have looked at laser pointer heat guns and thermocouple meters but am unsure if either would work to measure a coil...

I built my first box mod today with the sx350 from varitube and their hana clone kit. Everything works great except the usb charger. the light turns red but the battery voltage never goes up. its been on charge for 3-4 hours and still at 3.9 volts where I started. Am I jumping the gun here...

I hit the fire button and I always get 'low load'. Same with having nothing attached. Tried several known good atomizers with same result. Is is salvageable or is it junk?

I have the natural and I love the look and feel of the mod but im getting a really high voltage drop. In the range of 3.2 to 3.3v with a full battery. Ive sanded down the contacts to brass but still terrible volt drop. any suggestions to bring this mod out the graveyard?

Is there some trick to getting one side of your genny to end up on the opposite side of the button? I want my wick down and my button up but when I screw in the genny it never seems to end up where it last was. The wick side kinda creeps around.

I always felt that unless I used 32g kanthal my zmax was alittle wussy. Even at 15 watts on 30g it never really had much umph. I just got 2 IMR 18350 and tried it stacked and WOW. With 30g kanthal at 15w it instantly melted the top wire from the wick. im down to a friendly 4v on a 1.5 ohm...

so like many I started with clearo's and on to a vivi nova. And have ended up sub ohm vaping with ribbon kanthal on a genny. But I want more! I wanna have to limit my hits cause there is toooo much vapor. Where next?

Anyone seen these in stock?

Lost the white seal under the positive post spring and have no idea where to get a new one. Anyone know where you order parts for these? Went to Smoktech.com and they dont even have the RSST listed.

I set my VV zmax to 6v and with an multimeter it reads 6v. The battery voltage is about 3.7-6 though if I test the battery. But when I set my zmax to 5v it only says 4v on the meter? Put a new battery (4.2v) into the zmax and still at 5v setting the meter reads 4v but the vapor shoots up so I...

I am somewhat new to clearo's and tried a dry burn with one. I pulsed it till the coils were glowing and the wick looked white again but now it has a really foul burnt taste. Did I burn it too much or too little?

Do the videos you see with people getting massive amounts of vapor on their genesis attys use 100% vg? I get alittle more vapor than my vivi nova with 70/30 and it uses ALOT more juice.

Im somewhat new to SS mesh wicks. Im trying an unoxided method developed by Petar K. Coil look beautiful and without liquid doing a dry burn they all light up evenly on the wick. So I dont think I have a short. But the vapor is low and very harsh. Im using 24mg 80/20 liquid and ive tried...

I set up my ss wick with the petar k method and the vapor production is lowish but the smoke is very very harsh. Ive used the cotton condom method and silica wick and both make better vapor and the smoke wasnt harsh like this. Nothing ive done yet on my aga t2 is even close to the vapor on my...