Search results

  1. S

    Uwell Crown Rba Leaking

    Been playing with this thing for a little over a week now... I'm not at expert but, I have noticed that, if I pull apart a KGD cotton pad (uhh... bad at visuals, pretend its two ply toilet paper?), cut the wick the same width of the coil pass the wick through the coil and fold it up, (like the...
  2. S

    Post office workers have an allergic reaction to flavoring being shipped.

    I hope nothing comes of it but decided it was worth mentioning because the story is repeated every 30 minutes on ktrh in Houston.
  3. S

    Post office workers have an allergic reaction to flavoring being shipped.

    Apparently the post office called hazmat when workers were suffering allergic reactions, they determined flavorings that were boxed up and not leaking, awaiting shipment, were the cause. I heard this on the radio then searched for more on the story, this is what I found: Seven...
  4. S

    Big Tobacco proposes open container tank ban for e-liquid

    I just checked out the vuse for free in the coupon mailer they sent out to Marlboro members (don't look away I know what you are thinking 0.o) and they are sure to give e cigs a bad rap, they are using 4.8 % or 48mg/ml liquid, way to high of nic content imho. If they would have labeled the...
  5. S

    Aspire Bottom Vertical Coil and Nautilus Mini

    Wow, I must have gotten lucky, or I am not to picky at all. I came on to see how many ml or tank fills yall get before the atomizer goes bad or loses all quality vape. So far I haven't gotten an atty to quit working, but I notice the wicking ability drop in the bdc's (aspire or clone) after...
  6. S

    Smoke Juice Storage Tips

    I thought I would add my 2c.... I just looked it up and my last post was January of 2010, I had quit using my e cig before then because of leaking issues battery problems and etc... I took all the liquid I had and put it in off-brand zip lock baggies in a cardboard box in the closet. Since then...
  7. S

    ZFM Zero Filler Mod

    Hmm... I am not sure what type of silicone tape you are referring to... Can you please post a link? The only silicone type I have used or found by google has no adhesive but creates a chemical or mechanical reaction when stretched and layered or wrapped around an object. My science is fairly...
  8. S

    ZFM Zero Filler Mod

    801 super glue update: Well... been using it almost every night changing between two carts and when it works it works great... when it fails (and they both have, and been 'fixed' worked fine one or two fills and same things happen), it is a complete mess... It seems as if the vacuum/glue seal...
  9. S

    The Micro Juice Box

    Awesome idea, I like it a lot, now thinking of a way to do it with the two piece 801 cart... Maybe a tiny thumb screw through the mouthpiece and cart going to the other side unscrew it for a second so one side has a break in the seal and screw it back in to break the seal and allow flow... If...
  10. S

    ZFM Zero Filler Mod

    Another 801 update: 1/2 of the way through my 4th full cart the glue around the seal seemed to come half undone. The cart leaked about half of what was left and it ran down the passthrough... I don't know if this was due to heat or the e liquid breaking the glue down. I finished off the cart...
  11. S

    ZFM Zero Filler Mod

    Might be a stretch to find depending on where you live but there are a lot of smoothie places around here and they use monster sized straws so they can put real fruit, jelly, or tapioca in the drinks and not have to worry about the straws getting blocked up. They may be too big (have not seen or...
  12. S

    a new hot modder juice box from germany!

    May be a mute point and I have done no research for this whatsoever, but has any one looked into a water-cooling pump for a pc? They run off of the dc power supply for the pc and a lot of things in a pc run at 5 volts (usb standard).
  13. S

    ZFM Zero Filler Mod

    Update on my super glued 801 plug: I started from scratch once again with an 801 cart and the silicone cap, glued the cap on with super glue by putting the glue on the rim of the cart (I used the glue on the cap last time and made a bit of a mess might have been the issue) this does not have an...
  14. S

    Contact the FDA - Before December 28th!!

    I read it, and that is a very well put together argument. Thank you for drawing attention to it.
  15. S

    Contact the FDA - Before December 28th!!

    There is one fatal flaw in posting about electronic cigarettes, they are not a tobacco product. This is a separate issue and I believe that posting on this topic and mentioning electronic cigarettes will hurt us pv users more then help anything because we would be conceding and supporting the...
  16. S

    ZFM Zero Filler Mod

    Is not option #4... Anyways, earlier I posted that this is working well with my 510, I haven't been using it so no update but I did chain vape three carts with it during the test. For my 801 (just came in this morning) it is great when I can get it to do more then give me the random shot of...
  17. S

    best 5v mini usb pass through

    A tact switch spst is either on or off, should be like a 'clicky' switch on a flash light, press once on then again to turn it off. Have you tried pressing the switch until it 'clicks' and letting go? If pressed and held it should stay on the previous setting, and depending on the speed you let...
  18. S

    best 5v mini usb pass through

    I just wanted to mark this thread to come back to it later, I like this idea but I believe the charger is rated too low (amperage wise) for the 18650's I just ordered. I think it would take as long to charge them as it would to drain them in the pv. I am curious as to what else we could tear...
  19. S

    ZFM Zero Filler Mod

    Instead of using a dremel on the silicone, you could probably use a sewing needle and thread/fishing line/really thin wire and string it through the plug and rotate one end, the needle would also let you decide how far you want to start the tip of your cone. I don't have any of the materials...
  20. S

    ZFM Zero Filler Mod

    With any luck.... I won't have any dead 801 atty's... you think it would be all right to skip that step and use a slit or x cut? If not what would be good to protect the atty? plastic wrap?
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu