Search results

  1. J

    Russian 91% vs Russian

    I lung hit. Just pull the air flow screw out of the 91%. I also found to build the "volcano" coil / "dragon" coil / "chimney" coil directly over the air hole in the chamber creates really good air flow. You can find the volcano and dragon coil build on here and the chimney one on Rip Trippers...
  2. J

    Better RDA

    Igo-W? The cap between the two is interchangeable.
  3. J

    Russian 91% vs Russian

    What is the difference between the 91% model and the regular model?
  4. J

    Watts do not matter. Its all about wire temp. Read on…

    Glad you guys responded with some ideas. I was thinking about it off and on throughout last night. My initial thought is that I should be reading the coil from the bottom to avoid the vapor all together. This can be done by mounting an IR window to something and make that the "atomizer...
  5. J

    Watts do not matter. Its all about wire temp. Read on…

    So I found this pretty interesting based on yesterdays messing around. Yesterday the coil was a dual .4 ohm 28g Kanthal wrapped at .81mm ID. Today the coil is a dual .8 ohm 28g Kanthal wrapped at .5mm ID. So here is my simple analysis of this. The temps are basically the same, but...
  6. J

    Watts do not matter. Its all about wire temp. Read on…

    It depends. My higher end systems all have adjustment for transmission. Mainly for IR windows. I would have to have a sample to know. It is pretty quick to figure out. Even then the close quarters of the target would cause issues potentially because the acrylic is still going to emit IR...
  7. J

    Alexander Mundy's Magic Twisted Ribbon

    Yeah ditto. It is a blast. You are correct with the point IR radiometer. They are super inaccurate, mainly due to the fact that most of them cannot adjust for emissivity. I can make something that is 300C look like it is 100C or 500C just with a simple setting. I would also think that +/-...
  8. J

    Watts do not matter. Its all about wire temp. Read on…

    Testing with a draw brings in some new, and very hard to overcome challenges. First and foremost is I need line of site for the camera to work. IR doesn't "see through" anything. It picks up IR energy via the three forms of heat transfer (convection, radiation and/or conduction). The huge...
  9. J

    Watts do not matter. Its all about wire temp. Read on…

    Cant really do anything with this stuff yet. I will set up something simple for the different sizes of Kanthal then we will go from there.
  10. J

    Alexander Mundy's Magic Twisted Ribbon

    ID not sure, just used a small screwdriver. Guessing 5/64. 4 wraps. .4ohms. KTS+ with an RSST. I forgot to take coil voltage just because I was goofing around. I am doing a lot of IR stuff for another thread about wire temps. It is in the main modding forum. These are just initial tests...
  11. J

    Watts do not matter. Its all about wire temp. Read on…

    Here is it "tuned" and also in red/blue which most people prefer
  12. J

    Watts do not matter. Its all about wire temp. Read on…

    Just goofing off so far. It was on a mech device. Battery was not fully charged by a long shot. Guessing 3.3V or so at the coil. Battery probably in the 3.8 range. On the Mundys coil, it is .5 ohms. .8mm x .1mm spun and wrapped the Mundy way.
  13. J

    Alexander Mundy's Magic Twisted Ribbon

    Your magic wire in IR....... 539.8F was the highest observed temp.
  14. J

    Watts do not matter. Its all about wire temp. Read on…

    For those of you that have read the Mundys Magic Wire thread. Here is one in operation. 539.8F was the highest observed temp.
  15. J

    Watts do not matter. Its all about wire temp. Read on…

    Okay, simple little test using a dual coil set up that I have. 28G Kanthal at .4 ohms. For now, this temp is just a base line. No settings are done on my part to adjust for certain parameters. However, it should be fairly close. The file created with these short vids are almost 1 gig...
  16. J

    Watts do not matter. Its all about wire temp. Read on…

    I thought you guys only cared about the wire temp. I only read the first couple of pages and the last couple of the thread. Juice will create another variable. Juice also creates an entire other discussion, much of which is user perceived. For example, some people want a hot vape, cold...
  17. J

    Alexander Mundy's Magic Twisted Ribbon

    Its an RSST, so it is a tank on bottom with vertical wicks. I drilled out the original refill hole to make it a wick hole. Then, drilled out a new refill hole on the opposite side of the negative post. Yes, I prefer something with a tank so I do not have to constantly drip. Although my dual...
  18. J

    Alexander Mundy's Magic Twisted Ribbon

    Okay, turned it horizontal and re wicked it. Ran cotton through the middle then wrapped the cotton ends around dual SS 500 mesh wicks. Wrapped one strand of cotton yarn around the whole mess just to keep it together better. Taste is amazing and no dry hits. Now I only have one more problem...
  19. J

    Alexander Mundy's Magic Twisted Ribbon

    Yep.....you are correct. I cannot keep it from burning and dry hitting. Will spin up some of the smaller stuff today and try that.
  20. J

    Alexander Mundy's Magic Twisted Ribbon

    Its hard to tell what is going on in this image, but it is .8mm.1mm Mundy's magic wrapped 4 times around ceramic wick with a SS inner core on an RSST. Comes in at .45 ohms. Initial taste isn't all that good, but I am going to give it a few days to work itself in. I took a pretty bad burnt hit...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu