Search results

on a 91%, once you remove your 510 pin, the little screw right there at your battery connection, you will see a shaft with a flat head slot on it. Hold the air block from spinning and tighten down that shaft. Make sure that the block on top stays straight, if not it will short out with the...

I guess they care more about their Atlanta store than they do about their original store in Woodstock. I've never been to the Atl store, but I've been to the Woodstock store about 6 times, since it's so close to me, and I've gotten people and service raging from bein ignored in an empty store...

yup ketchup cleans it right up because it has a lot of vinegar in it. It's prefered by many since it is cheap, usually in everyone's fridge and is easy to work with. There are many ways to clean copper, as long as you're not using an abrasive, there is no wrong way to do it. Just keep them...

The best way to clear juice or condensation buildup in a protank, MT3, evod or any other bottom coil clearo, is to take it off your mod, ego or device, hold a napkin over the mouth piece, and give it a few quick flips holding it by the base. It will fling out any excess juice and condensation...

If you use the pipe cleaner with the base and coil still attached, then yes, it is possible.

Simple and cheap, but efective If all you want is to clean it, soak it in white vinegar for a few hours, you'll be amazed at how efective it is at cleaning copper. When done, just rinse it in water and dry it out. If you want a natural patina to form with use, no further action required...

From your pic, yes that's a standard protank or clone of a protank, which is 19mm. It is more than likely a clone, since all my Kanger protanks came with the 19mm beauty ring. If you were in the USA I would just ask you for your address and send you a couple of them, I have about 3 or 4 that...

and forgot to mention, don't use the factory drip tip, it's too restrictive and creates too much condensation, causing the juice spitting in the mouth and restricting the wonderful snap crackle pop

Or use twisted wire! My Kayfun has never crackled as much as when I use triple twisted 32 gauge. 8-9 wraps around a 5/64'' drill bit gives me around 1.2-1.3ohms of crackly vaping goodness!

but for a Protank, scroll in the drop down menu to the 19mm version. It will taper from the 14mm or so that the ego type battery is to the 19mm diameter that is the protank.

If this is a route you want to pursue, there's a progression you have to go through. Remember, you had to crawl before you learned to walk. You already have a K100, you'll need a RDA, I would highly recomend one that had adjustable airflow and allows you to build single and dual coils...

It sounds like that might have been refering to Bad's Caravela pic

Like Clark said, the K100 is just a mechanical mod, so basically it's just a battery holder with a momentary switch. You control the temperature of your vape and the vapor production with the atomizer that you attach to it. If you want more vapor, go with a lower resistance. What topper are...

I'm used to seing vape related rants or equipment help requests and such, but I'm just not following you. Something seems to be seriously bugging you and you comments seem to be all over the place, what brought this on?

That's Goya's slogan. It means: If it's Goya, it has to be good. I grew up in Puerto Rico, and a lot of their products are made and/or packaged there.

I have it, I use it as an additive for TFA Black Honey

Coumarin is a wonderful, smooth & clean pipe tobacco, very enjoyable.

I'm vaping this right now, although I did 10% coumarin, 5% maraschino & 4% toasted almond, all Flavor West from Mt Baker

"Si es Goya, tiene que ser bueno!"

As far as water to thin out VG, try around 5%. A lot of vendors add water to their mixes too, so just because you were using a 80PG/20VG blend (assuming you were buying it not DIY), doesn't mean that it doesn't contain water. Coconut water is great! I'm hoping that this helps you keep...