Search results

i don't know. could you post a pic of how it should look if you wouldn't mind?

yeah the picture was of what it does naturally after a few hours after i've properly installed a tube with a v on the bottom. the tube is pushed all the way to the top of the nipple but after a few hours the tube slinks off the nipple by itself and into the bottle and starts squirting juice...

the tube pulls off of the metal on its own. that's the problem. thanks guys.

it's still hitting the bottom corner on the inside... but yeah... had to cut it again today as a hole formed again while i was at work. i'll be switching to a new bottle and tube when i get home.

hey thanks for all your suggestions guys... i have two authentic reos: a '14 grand with old gold contacts/feed tube, and a new p67. i've only bought rm2s, and a couple of atomizer clones (to see what i like and what i might want to spend the big bucks on) recently since rm2s weren't available...

yeah the screws in the o16 posts don't screw in all the way and when mounted are precariously close to the top of the cap, there's maybe a millimeter of room, so if there is a poor seal and the cap becomes slightly unseated and tips ever so slightly one way, a post screw can easily make contact...

o16 clone's orings aren't working, the cap has come apart and shorted my reo twice now.... real bad luck with these clones :( anyone know the size of the orings/a good replacement?

hey there. i got a clone of this 016 with some flimsy o-rings and the top cap won't stay on. it has actually shorted my reo twice coming apart while firing and hitting the post screws because of the bad seal from the cheap o-rings. lots of searching has landed me here. anyone else replaced them...

that's the one. the threading or the shortness of the bf pin is the issue. wish mine was perfect....

thanks for all your helpful suggestions! i finally located the missing grub screw and after a bit of finagling i was able to get the origen clone to work for me on the p67!! it's working ten times better than the aged rm2s i'm used to!! i think i'll buy another of them for when i get my grand...

so bad luck with both of those... the hadaly clone came with a bf pin that is not long enough to keep the positive post in place. i push it in but it just spins around and detaches when i get a coil in. any ideas on where to get a longer one that'll fit? then i lost one of the grub screws on...

i used the one that came with the p67. it looks the same as the grand bottles; the grand is all i've used (other than crappy leaking tanks and cigalikes in 2013, before i found out about the grand). my grand has old connectors. what happens in the p67 is the tube sinks inside the bottle somehow...

i can get the feed tube to stay on the nipple for about 20 hours. it slowly works its way off the top of the mod and then i end up squonking expensive juice all over my life (holi smokes, now sold for $20 per 7ml so i can't afford it anymore and i'm not even able to enjoy what little i have left...

i think that's right, jifjifjif, the nipple is just a whole lot bigger than the one i'm used to. is slightly wider diameter feed tube available? yes msloud, it is the tube/bottle that came with the mod, looks the same as the grand bottles. thank you for the tip, i'll try that next time!

hey so just got this thing. is there a better bottle for it? the metal juice feed is so much bigger than the one in my grand and the feed tube just pops off of it. i can't get the feed tube to stay on the connector - probably wasted $20 of ejuice trying. very frustrated. any help would be...

i'd really like a sparkly gold toned or brass p67 or lp grand! i have a sparkly red grand and a shiny silver p67... spaaaarkles

thank you!

got my p67 today, and it's super nice. so excited for the new atomizers! the rm2 is hanging in there... what's a beauty ring?

i don't have an lp to compare it to so it will probably have to go to the spa, but now you've got me thinking....! i bought an all-aluminum p67 and was eyeing a post about how to give it a chrome-like mirror finish.... but i don't have any metal files or sandpaper..... hmmmmmmm. maybe that will...

i've only ever done single coils!