Search results

  1. J

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    hello all, i know i am tardy to the party but i will start building this tomorrow, at least moding the box. i Have been studying this build for a while and need just one thing clarified, with the latest build update 9/23/2014 on page 34, does the switch need to be rated, if so will a n-mosfet...
  2. J

    Vapor Flask V3 DNA40 Clone thread

    thanks for the ohm range just checked the voltage and i get exactly .05 from both battery caps to the atty when firing. but still theca if cranking down the battery cap does not seem good for the device. any ideas on that? and the weird reading when the cap is tight but not getting a good...
  3. J

    Vapor Flask V3 DNA40 Clone thread

    can anyone refresh my memory on the ohm range for TC builds?
  4. J

    Vapor Flask V3 DNA40 Clone thread

    @dwcraig1 and @Quantum Mech sorry for the delay. I do have it "working" thank you to everyone for the help. I say "working" because i really have to torque down the battery caps. On the 510 side just a bit of pressure, but on the screen side i probably have to go an additional 45-90 degrees...
  5. J

    Vapor Flask V3 DNA40 Clone thread

    Saw that too. Not sure how I could do that test. If you could tell me i could try and do it.
  6. J

    Vapor Flask V3 DNA40 Clone thread

    i do have a volt meter. That worked @dwcraig1 , you are genius! ahhh i don't get it why did it work? Here are more photos of it working with the wire, my batteries, the battery cap, and battery cap threads
  7. J

    Vapor Flask V3 DNA40 Clone thread

    Here are some more up close photos. to try and help everyone and then you all to help me :-) both black wires out of the fire button terminate to the top of that blue board in the back front side of board up close Back side of board up close I don't think this picture will be...
  8. J

    Vapor Flask V3 DNA40 Clone thread

    Yea there are two black wires coming out of the fire button area. On of those it the wire with the torn insulation
  9. J

    Vapor Flask V3 DNA40 Clone thread

    Ok so I cleaned out the battery cap area pretty well. But how clean do they need to be. I would say it is much more metal than anodizing/powdercoating. What of it is too loos in the battery cap. Is there something I could rap the battery cap in to make sure it is making a good connection? Just...
  10. J

    Vapor Flask V3 DNA40 Clone thread

    it is coming off the fire switch. it could be touching the screen or top plate at different moments. i would have no idea
  11. J

    Vapor Flask V3 DNA40 Clone thread

    actually there it is i think in the last picture there is some insulation off the wire under my screen. do you see that. could that somehow be causing all this? i mean i get that exposed wire is no good but could that be the cause of all of this?
  12. J

    Vapor Flask V3 DNA40 Clone thread

    no buzzer but does tell you low voltage
  13. J

    Vapor Flask V3 DNA40 Clone thread

    thanks @dwcraig1 that helped a lot. super easy to do, with a little guidance ok so here is the sled fully removed. things look ok is me the positve pins do look a little angled. does anyone see anything i don't here that i should be looking at?
  14. J

    Vapor Flask V3 DNA40 Clone thread

    gotcha. Ok perfect. I think i can do this :-)
  15. J

    Vapor Flask V3 DNA40 Clone thread

    so to remove the buttons, i just pull them straight out? away from the device, like i am pulling a thumb tack out of a cork board?
  16. J

    Vapor Flask V3 DNA40 Clone thread

    @Quantum Mech, by battery sled do you mean the tube and the top positive connection? @dwcraig1 have you pulled out the whole sled? anything i should know before trying to pull it out and start looking at the positive connections?
  17. J

    Vapor Flask V3 DNA40 Clone thread

    @dwcraig1 sanding didn't seem to do anything. I think the ground in the top plate comes from the screws. the crew touches non coated metal, does a mod like this require much more ground than this? sorry still a newb to actually working on my mod
  18. J

    Vapor Flask V3 DNA40 Clone thread

    @TheBloke So I am ArtVandelay from the FT thread. I was watching a lot of seifeild that night and could not come up with something clever :-). Alexander just so happens to be my first initial and last name, again wasn't felling clever. I think you are right that i drew the short straw here...
  19. J

    Vapor Flask V3 DNA40 Clone thread

    Hello all thank you for the help thus far. a few quick clarifications to hopefully better explain the situation. When i first got the device i realized there were a few problems with the battery cap threads. i cleaned those up as best possible yesterday. the battery connection problem has...
  20. J

    Vapor Flask V3 DNA40 Clone thread

    hey guys and gals, so my SXK flask is straight up sucking. each time i think i fixed the problem and i do not. there is something strange going on with my Black 60W unit. Any advice would be greatly appreciated. i will be submitting this as ticket to FT as well but i have read on the FT...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu