I was going off of what I was told at the vape shop but now I'm not really sure. Tried nickel and titanium TC modes and am having the same issue with really hot vape and high wattages at 100 degrees. How can I find what type of material this coil is? I've been looking everywhere.
Has anyone had any success using TC with the gt8 core SS coil that comes pre installed with the Revenger X kit? I've been finding the temperature control to be a bit out of whack. I did a small experiment which leads me to beleive that the TC is not really doing anything.
TC range is from...
Thanks! That will definitely be useful in the not so distant future. There are some spots on the button contact that will need polishing.
Sent from my HTC One_M8 using Tapatalk
Great thread!
Amaretto 17.5% 2.5/5
Peaches & Cream 17.5% 2.5/5
Both of these were way to strong in my dripper! I even get headaches from them. Right after mixing they were not bad but after a few days of steeping the flavor was way too strong. Had to let them breathe for two 12 hour intervals...
One spring loaded one magnet. Spring loaded was squeaky clean (I've cleaned it since as well). Pin is making good contact now but could very well have been the issue before. I would test... but don't want to start venting another battery!
Sent from my HTC One_M8 using Tapatalk
When firing the mod normally I think there wasn't proper contact between the atty pin and the mod... Overall the issue was basically lack of attention to connection contact, but everything is working great now [emoji2]
Sent from my HTC One_M8 using Tapatalk
I was using a wotofo ohm reader, but I think the problem was with the connection between the ohm reader and the mod. The mods were screwed all the way in but on the reader the attachment may not have been screwed in all the way causing a short and the battery to get close to venting (I could...
I figured this wasn't the issue due to the button heating from the drop test with the ohm reader (and the issue never came up before). But, actually I think you may be right. The wotofo mod is working extremely well now, but the mutation still seems to be misfiring. Will have to get a multi...
All of a sudden, whenever I fire my Mutation X V2 mechanical mod with an RDA on top nothing happens. I tried doing a voltage drop test on my ohm meter, but I don't get a reading and the button gets really hot!
Here is my troubleshooting process so far:
1. Tested RDA for shorts - none exist and...
I've been using these coils for the last month on my device and would like to figure out the heat capacity and flux on steam engine before I get and build the coils on my first RDA.
Has anyone taken apart or knows the specifications of these coils including gauge size, number of coils, coil...
Hi all. I want to get into making my own e-liquid seeing as the process is straightforward and much cheaper, but I feel like living in Canada is not ideal for doing this kind of stuff right now. It seems like all the suppliers I've seen so far either do not sell nicotine base liquid or only sell...
Interesting stuff! Seems like there are a few trade offs to think about. The concept of an optimal build would be interesting to add. There are ways of dealing with subjectivity for this... Anyways thanks for the tips.
Hmm.. honestly never thought about heat flux or capacity for this build (first attempt at buying a rebuildable ever). Out of curiosity, roughly what HF/HC do you go for? I'll test out this build but might take your advice on a higher gauge wire. Anything VW will have to wait a bit (pockets...
Are you sure? See the link I posted. It's a pack of 10 coils and doesn't mention any specific setup so I'm assuming it's 0.5ohm each.
As for the power, given 4.2V with 0.25ohms comes out to ~70W. Probably lower after its built so I'm hoping it works out.
Thanks! Great to hear. I've edited the post to include details of the coils and setup. For some reason I heard the doge x v2 won't work for a single coil setup, but that would definitely be a quick and easy fix if possible.
I bought the above mentioned battery as well as a pack of pre-built kanthal twisted micro coils to put on my new RDA which has yet to arrive. I realized I ordered the coils at 0.5ohm when what I actually wanted was 1ohm each. With a double coil build for the 0.5ohm I'm assuming that I'll be a...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.