Search results

I have same problem when I direct lung. I think it's either too much vapor which maybe gets inside sinuses or drawing too hard on an atomizer with a tight draw, kind of like blowing your nose too hard.

Same here, if I exhale through nose it immediate gets wet lol also dl for me makes my sinus stuffy

Not sure, don't have one. Check orings on tank and coil. Maybe check to see if coil is flooded when it leaks.

I was wondering if the heat treatment/preoxidation part applied to vaping. I've heard kanthal comes preoxidized and the process of winding the coil produces stress in the wire therefore requiring further oxidizing. Are they referring to oxidation performed by themselves or recommending how to...

Thanks for the reply. Does the info on link below apply to vaping as far as the preoxidation, stress relief and fabrication goes. Kanthal APMT — Kanthal

Is there a need to oxidize a spaced coil even though it heats up evenly from the get go? Would it be healthier not to oxidize it compared to low power dry firings as far as not damaging the kanthal? How do you clean the coil for rewicking, high power dry burn? Is that safe on a already oxidized...

I have the same problem with the juice fill screw on my Triton 2 and after one year I still use a wrench. I do like it with the 1.8 ohm coil though.

If I'm using only one tank I can go through two tanks a day and rewicking twice a day is too much work specially since its a tank not arda and wiping dark condensation of all the hardware is time consuming.

I don't necessarily think gunning up is something that can be fixed, although I'm open to suggestions. My main concern is inhaling the black stuff. I'm pretty sure I do inhale some since the black stuff is all up in the chimney and inside drip tip. No tc here. I'm running 11 watts on a 1.7...

Ill take more pictures when I rewick. Bottom of drip tip.

I'm using a vanilla butter nut flavor but it also happens with other juices. I mtl this tank. This would also happen on my Triton 2 with the 1.8 ohm coil, after a couple of 3ml tanks, when I cleaned the condensation off the drip tip and chimney you could see little specks off black stuff which...

I was wondering if vaping on a gunked coil is unhealthy. I'm using a Kayfun 4 and if I don't change the cotton after every tank, (taste only gets bad after two tanks) I get a lot of black stuff inside the chimney and I assume into my lungs.

You man this video? It's a bit hard to tell since he is during that coil at high power. When it cools the center is hotter.

All attempts I've made have not heated evenly but mostly from inside out. Some coils do heat with a slightly larger inside area. When watching drifter's videos of the coil jig I don't think his were heating evenly either. I've seen your subtank trio pictures of the heated tmc but do you have a...

Could pinching the coil with ceramic tweezers aid in oxidation for a coil that has not achieved adhesion or a non tension micro coil?

Samething happened to me, got rx200 than downgraded to cuboid for pocket. The joyeteck cuboid has some issues though, like a shallow 510 without much springness so many tanks have large gap. Also the 510 is not flush with the mod so there's always a gap which won't help if you drop it...

Get vg based nicotine. For me pg adds to throat hit and even 6mg nicotine is too throaty for me. As far as throaty flavorings I have no idea but am also curious as to what ingredients do that. If you are trying to up your nicotine intake per puff, find the nicotine level you find smooth and up...

Check out this video. I use the cuboid's preset SS TC setting or you could use custom TCR settings which the video goes into. The wattage for TC dictates how quickly your vape ramps up, then the mod regulates to your set temp. You could start with 30 watts and maybe 350 Fahrenheit and if it's...

What's the best cheap kfm3 from fastteck?