Search results

A quick question - when you trim the tails for wicking on a Kayfun, do you trim on the top of the wick and bend over the bottom of the wick to the deck or do you trim the bottom of the wick and bend over the top of the wick over the trimmed cut? Thank you for the help! Steve

Thanks pwheeler and Rattlerx for your builds. I have the wire and I will try them both. Have a great day! Steve

Hi everybody! I have been using the Nuppin on my first build of dual single 29ga / 1.6mm / 7 wrap. I am ready to try something new. I vape from 0.5 to 1.2 and was wondering if you would be willing to share some your favorite builds? I was thinking on trying some dual twisted 26 or 28ga. Thanks...

Just checked my mail box and there was a package - a Router DT. Man, does that look great together. Just switched over and it vapes great! Your kindness continues to humble me. My deepest appreciation to all! Steve

Hi everyone! First build and vape. 29ga / 1.6mm / 0.64 ohm My Granddaddy used to say "if it could be any better, you're lying". I have been vaping for 5 years and this is the best vape I have ever had. Thank again for everyone! Steve

It would be my great honor also! Steve

Thank you penguiness! I really appreciate your kind words! Steve

I have just finished some of the previous posts and I see there are a number of people that offered their help and it was already closed by pdib. I would also like to express my sincerest gratitude and thankfulness to each of you for your kind effort and supportive words! Everyone in this thread...

To all the amazing and wonderful people on this thread! I received my mods late today and I am still in wonder of the selfless, kind, and supportive group of people that came to my side in this difficult time. I had vowed to keep my emotions in check for my wife's sake, but when I opened the...

Thanks Jeremy! I'll trial again.

I am getting really frustrated. How are you guys "un-rolling" the Delasco rayon balls? I cannot find the start. Is there a trick I am missing? Thanks for your help!

I use both Sally's and Tencel. In my tanks (KF, Fogger, and Lemo) I prefer Tencel for .5 and lower ohms. The "trick" to Tencel is like Holman said - wet it thoroughly with your juice before you install the coil. I think it wicks better than Sally's on the low ohm tanks. I prefer Sally's on my bf...

I have been using rayon for about 6 months and have been very pleased with it. I trim my tails as shown in this forum, but I am still confused as to why trimming the tails makes rayon wick better. Why doesn't full wicks work just as good as trimming? I don't understand the difference between...

Hi Mike - try this link: TIDI Cotton and Rayon Balls - MedSupplier.com Rayon balls are the bottom two - be careful because the top two balls listed are cotton

Thanks AMD! I'll give it a try. Steve

awsum - I am wicking kfl style with plenty of cotton on top of juice channels AMD - it does not leak when using, only with filling. I thought the 2nd hole in the top was to release air pressure when filling with the 1st hole and therefore no need for closing off side air holes.

I have the new V5 and no matter what I try it leaks out the side air holes when I fill. I use a syringe in the larger of the two top holes, go slow, and it still leaks. I don't understand why since the second hole on top should release any pressure. Anybody else having this problem? Any...

Great job super_x! Really appreciate your effort and knowledge. Been using this method of yours with perfect coils. Could not be any easier to get a great coil with minimum time and excellent results. Steve

I have both Tencel and Ramie, and I really like Ramie in my KF's. The "trick" with both Tencel and Ramie is to pre-saturate your wick before you insert into your coil. I first determine size (based on coil id - they do not shrink), and then I gently form the wick and put it on some wax paper and...