Search results

  1. I

    Cool fire IV and Isub Sub ohm

    J.c. most of the sub ohm tanks have a much larger coil than what you are accustomed to. Secondly 20w is also much more power than either of your old devices..... Both of your old devices ran around 8watts..... Third is the sub ohm tanks offer much more airflow around the coil. The crackling...
  2. I

    Prize List for ECF's 15 millionth post!

    Good luck to everyone
  3. I

    Ended Prizes! 15 millionth ECF post...

    Doomed!!......Nice Paranorma
  4. I

    Ended Prizes! 15 millionth ECF post...

    Still trying to be the 14,999,999 post.....
  5. I

    Ended Prizes! 15 millionth ECF post...

    I would love to be 14,999,999.......
  6. I

    My coil keeps going bad.

    Ok there is problem one. Your draws (on that setup) should be slow and consistent into the mouth, then inhale into the lungs. They can be long draws but not forceful. Too much force on the inhale will cause the flooding you explained in an earlier post....."juice in my mouth ". ... the kit you...
  7. I

    My coil keeps going bad.

    Hi Sansa Let me say that I had many issues when I bagan. Your device is best known as an eGo type battery with a eVod clearomizer. With that being said, how are you taking your draws on the device?
  8. I

    Juice consumption at different wattages, ohms and volts

    Hi Juma. In general the answer to your question is yes. Generally when you run higher wattage it allows the coil to heat and vaporize your liquid at a faster rate. That being said you are comparing across different tanks, with different heads so one tank may use more or less than the next...
  9. I

    Modding my Aqua v2 for post-less deck: how to solder a new head on a screw? (Steel / stainless maybe)

    If I where to attempt something like that I would begin with a 5mm post cut to length then put it in the deck..... hold the deck firmly (preferably in a vise) then center the bit and drill down about3/4 of your depth. Tap the threads and insert screw. I would try to find a buddy who has a drill...
  10. I

    Modding my Aqua v2 for post-less deck: how to solder a new head on a screw? (Steel / stainless maybe)

    Why not just open the center of your m5 screw then tap say an m2.5 hole into the center? Still could find both of those parts easily and not have to deal with all the safety questions that arise from glue or solder... just a thought. Good Luck. Happy Vaping.
  11. I

    box for diy

    The 1590G is much larger than the Smok M . Plus the angle on all sides sloping away from the back towards the door side makes them undesirable for me personally. Too much work to get them close enough to flat. With that said they are easy to build in. I have built quite a few mods over the...
  12. I

    Weird question/ silly story

    Hi Sally. I can tell you that when I was using the silica clearos, There really is nearly nothing that can kill them aside from tooo much voltage. Just do your dry burning ( with pulsing on/off every few seconds) and once you see the coils glowing evenly rinse the remaining residue and dry burn...
  13. I

    need help with what tank to get

    Hi Artur, So with a little searching we know that the iStick will go to .5Ω no problem. Eleaf recommends the Melo clearo for that (Wonder Why??LOL) mod. I have never used a Melo but I have seen one. They look nice but I personally am enjoying the Subtank mini from Kanger. the thing that kept...
  14. I

    I'm at a loss...

    Jc I cannot properly answer the question about the Nautilus. ....but if I where to bet my answer is yes it will work just fine. Here is the thing about coils in general... they are consumables. Meaning that they will wear out. The main determining factors for how quickly they fail as I know...
  15. I

    I'm at a loss...

    Hi Jc. So it appears that you have found a reliable power source and a good feed system. All you need to iron out the liquid situation. I began Vaping almost four years ago. ... and I too spent way too much money on equipment until I found the ECF. ... I realized that my nic level was too...
  16. I

    Rda/mech mod connectivity issues

    Hi MJ. Could you use an o-ring from a different device.... like from the fill screw on a kayfun..... to act as a spacer? I have had to do that with a couple of my atties... A trip to home depot will likely let you find one that fits correctly and holds the top post in place like it was made that...
  17. I

    VOTE: Need help picking a Hades all stainless or with gold ring?

    Get both..... put the gold rings from the brushed one on the polished body and the ss rings with the brushed body...... I know that doesn't help with the decision but would be the best look.... good luck with the decision. ..
  18. I

    Teaching an old dog new tricks

    Hi Doc. Welcome to the Ecf. I agree with you on making liquids.... I have been DIY for about 2 1/2 years.... just take your time and measure carefully. Read everything you can to get a good understanding of what is and what is not good practice Good Luck. Happy Vaping.
  19. I

    It's so easy! How to comment. FDA need to know you exist!

    These proposed regulations, as they are currently proposed, will eliminate form the market a viable alternative to smoking cigarettes. They will cause many who have successfully made the transition from smoking to electronic cigarette use( here fore called Vaping) to return to smoking. They will...