Search results

It has changed unfortunately. I got a new bottle today and it tastes different than what I still have from a couple years ago. It always had a sweet and nutty flavor to me and the sweet is gone

If you have a Provari, try out the 3.0 ohm cartos

What is just to the left of the first provari(extended end cap), it looks to be carbon fibre, is it just a holder for the provari?

I feel better about the money I have spent on vaping now, I only have one provari Been vaping since Aug 23, 2011 and no analogs-- two days left to make 4 months

Check youtube for videos on cleaning the ego-t, the ego-c will be similar but much easier to do. You can actually wiggle the spike loose by hand with the ego-c to check/clean the coil and wick

How old are your ego batts? Are you chain vaping? I can usually get a day out of my 650mah ego batt on 2.0 ohm boges, except on weekends

Vinyl, I will never use rubber ever again, I tried it once when my original chibi grommet started to leak from my method of filling(blunt needle between grommet and carto). You smell the odor of the rubber pretty quick when vaping MikeE3, about what I was thinking of but the local hardware...

I use chibi's and some homemade tanks and they work very well The vision extremes can be a pain, the mouthpieces come out too easily and then they leak, I have used electrical tape to hold the mouthpiece on, just to have them leak out the battery hole. I haven't looked at modding them yet to...

Looks more like a potato launcher than ecig

vaporkings has a good price when you buy 10- 5 packs. I don't remember what thread it was, but I entered 20- 5 packs into their checkout with a discount code and the total was about $101 with free shipping. These were unpunched boge ss

The provari is made well, it limits amp output to 2.5 and under which should keep you from popping(destroying) any atty, carto, or whatever else you may use on it. They work on the 1.5ohm dual coils at low voltage but get better at higher ohms and higher volts. Initially I used my provari on...

I used quite a few EMDCC's that were all metal, no cracks, no leaks

If you want to figure watts, its (voltage x voltage) / ohms So if you are using 6 volts into a 3 ohm load, you are using 12 watts, and since volts x amps = watts, you are using 2 amps. The wires are pretty small on the cartos so you cannot keep upping the amps to them before they pop and lower...

I think the replacement atty cost is the big improvement, they use type A tanks so far. And some of the reports so far, they leak too

Possibly something along the line of these: Acorn Tank 2.4-2.6ohm They do have them with different resistance and have cut CE2's. Read about them as I haven't used one. All the needles I have are blunt tipped, no sharp pointed ones needed to fill a chibi type tank and then you could just...

I think any carto starts to get clogged with flavoring sediment from first use and just gradually gets worse until the draw tightens up and adding one or two drops results in one or two drops leaking out the battery connection. I just filled one of my boges with unflavored nic just to see how...

It must be twenty drops, approx 1ml for the standard boge carto(3/8 diameter x 1.25" long), just top them off when they lose a bit of flavor or give a drier hit

Sometimes its the combination of factors that results in a good vape. Most of my liquids are 24 mg/ml nic strength but not all present the throat hit(or burn) that my marb reds gave me while smoking. After vaping for over 3 1/2 months now, I could probably live without the TH but the flavor...

I think there are some issues with the wicking of dual coil cartos in tanks that end up leaking. It might be why the smok carto tanks have the small holes in them

I actually enjoy a lot of juices with a 2.0 boge on an ego batt even with a tank, and the ego is regulated to about 3.2-3.4V I think I am going to try a couple slotted cartos(dremel) again and possibly unflavored juice. Slots to see if I can get more use out of a carto with my juice, it could...