Search results

  1. L

    Wow... I've been away a while... Good to see this place still up and running.

    Wow... I've been away a while... Good to see this place still up and running.
    • learfx
    • Profile post
  2. L

    My Latest Steampunk Mod

    Been working on this Steampunk mod on and off for some time now. It's a Variable Voltage pass through. It uses the TI PTR08100WVD chip, goes from 3.6 to 6.5 volts. I'm running it off of a 12 volt DC power supply at the moment. Steampunk design with electro etching and uses a touch switch to...
  3. L

    Scorpio Copper Mod

    I used the Ti PTN04050 booster chip along with a p-channel mosfet to create a touch switch. Incorporated a blue LED just under the hand made scorpion touch sensor. used 3/4" L-type copper. Images are electro etched. This mod uses 1 - 18650, flattop or button type battery. More pics @...
  4. L

    Copper Max

    There is a pin soldered into the cap and and a notch cut into the copper tube. I cut the notch down a couple of mm at it's stopping point and the spring tension forces the cap down, preventing the cap from spinning lose. I got the idea from Copper Tube Mods - A 3.7v and a V.V.
  5. L

    Copper Max

    From what I discovered, the stock switch on the z-max board has about 3.3 volts going through it. pressing the switch brings the voltage to 0 volts... So to answer your question, no. I don't have extensive knowledge in electronics but I think the smaller switch will last because there isn't any...
  6. L

    Copper Max

    I used the Zmax controller board out of a busted up clearmax mod. The housing is 3/4″ L-type copper Used acrylic to make a protective window for the display Used a remote tac switch in place of the stock switch two styles of acid etching on the body and caps. Uses 1-18650 flat top or...
  7. L

    Contest - Quick and Simple

    1 & 100 ftw
  8. L

    Skullz copper mod

    Thank's Robert
  9. L

    Skullz copper mod

    no one? Ok then will this chip allow me to use a .5 amp switch? http://www.madvapes.com/assets/images/NCP630-D.pdf
  10. L

    Skullz copper mod

    I want to use a Touch Switch in this mod..... 3 amp 5 volt pass through using a wall transformer.
  11. L

    Skullz copper mod

    Hello all, I don't have a background in electronics to speak of so I guess I'm pretty much a noob. I have made a VV mod using the mad vapes board with the power source being a wall transformer, and it works. I am working on a new copper mod and I want to make it a VV With a touch switch. I Want...
  12. L

    Stealth Mod

    This is my stealth mod :2cool:
  13. L

    Pimp Yo Clearomizer

    lol, I like the gold and silver idea. How about sewing needles? I redone the ones in the pictures using them. The eye of the needle works really well with the coil wire. No solder needed.
  14. L

    Pimp Yo Clearomizer

    Thanks for the heads up. I'm going to change it out and leave the plastic covering on. I didn't realize the juice had such a reaction to copper. :facepalm:
  15. L

    Pimp Yo Clearomizer

    Rebuilt CE2 XL Clearomizer with new syringe and nichrome wire. Used Cat 5 copper wire for the +/- connections. Haven't been able to get new wicking material as of yet. :2cool:
  16. L

    HALLOWEEN - CONTEST - Smokelessimage.com

    If my PV dressed up for Halloween it would be Freddy Krueger......... Because it's soooo Dreamy :2cool:
  17. L

    Pictures of your setup

    VV copper mod, Material used: 1- 4" piece of 3/4" L-type hard copper tubing, two 3/4" hard caps for the ends, vv kit from madvapes, 510 gold battery connector, blue led, 20 awg stranded wire, 3 amp temporary on/off switch, 5V-2amp 120 v ac to dc wall adapter, 3/8" brass insert for 3/8" poly...
  18. L

    Pictures of your setup

    Wow that's wild...What type of tank is that? Anyone have a link?
  19. L

    Pictures of your setup

    Nice, where did you get that tip?
  20. L

    Pictures of your setup

    L O Fkn L!!! :laugh:
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu