Search results

  1. Commie

    Advice for mother-in-law

    Thank you folks for some awesome suggestions! I stepped away from ECF for a few years (once I found my happy setups) and so fell behind on the what's new :)
  2. Commie

    Advice for mother-in-law

    Hmm, that is a fantastic idea. I should take my shoebox full of old mods to see what shape, firing mechanism, and button location works better for her.
  3. Commie

    Advice for mother-in-law

    Hi there! I'm trying to convert my mother-in-law to vaping, but am drawing a blank as to what setup to get for her. She's 79 years old and has some dexterity issues -- her hands shake pretty badly, though she still manages a cigarette lighter. I'd like to get her something that has fairly decent...
  4. Commie

    Steam Crave regulated squonker

    Liking it so far, but it does leak from the same place as mentioned on page 9. Just above the brass positive block. The instructions here show adding o-rings just above the block, and instructions on the vendor facebook page talk about adding an o-ring in the top of the 510 (as much as I can...
  5. Commie

    Erlkonigin question

    I have quite a few that I have issues with, Kayfuns, Fogger V2, Aqua. The only one I have that can remotely compete with the Reomizers is Taifun. But it's huge and heavy, which is why I was putting a lot of hopes in Erlkonigin. Good capacity, easy refills, small... If only it would work :)
  6. Commie

    Erlkonigin question

    I have an Erlkonigin clone that I am having trouble getting to wick properly My first attempt was to follow the videos and give it a very sparse, short wick, with ends barely dangling into the top of the channel. With my 50/50 PG/VG juice and airflow half open, it would wick fairly poorly, and...
  7. Commie

    Anima atomizer convertable?

    Has anyone tried converting anima atomizer (or clone) for bottom feeders? :)
  8. Commie

    Origen dripper on a standard Reo?

    Thanks folks!
  9. Commie

    Origen dripper on a standard Reo?

    I have a standard (non-LP) Grand, and I wonder. I have Origen in the mail, that I was hoping to convert for bottom feeding. Do you know if the *internal* chamber will fit inside the well? Cause I can grind off the bottom lip. As long as the atomizer part itself, ground down, will fit inside the...
  10. Commie

    How to improve wicking in a KFL?

    Thanks guys! After adjusting the airflow to be tighter, it works better. Somewhat unrelated question though -- how is it that a Taifun can handle bigger airflow? From my limited understanding, it uses the same mechanics as Kayfun? Just cause its wick holes are bigger?
  11. Commie

    How to improve wicking in a KFL?

    Nope, I got it pre-enlarged.
  12. Commie

    How to improve wicking in a KFL?

    I have s lightly modded EHPro KFL clone -- the airhole is enlarged. Works great, and the airflow is just perfect. Even almost no whistling. However, it seems to not pull in enough juice to the coil. Every now and then I end up having to cover the airhole and take a few sharp dry pulls to feed...
  13. Commie

    Which Kayfun clone?

    Thank you guys! I'll try one of those.
  14. Commie

    Which Kayfun clone?

    I have one of the Kayfun clones from FT, couldn't get it to work in an acceptable manner :( The whistling is driving my dogs insane. I've tried a few solutions, to no avail. The juice channels were too small out of the box, so I dremelled them out. Now it floods with a standard setup, or runs...
  15. Commie

    Is epoxy safe with liquids?

    It's holding the top of the Taifun chimney in place, so there should not be noticeable heat there.
  16. Commie

    Is epoxy safe with liquids?

    One of my favorite RBAs came apart slighty. I fixed it with JB Steelstik. Unfortunately, it's inside the tank, where it will be in almost constant contact with the juice. Is it gonna be ok? The epoxy is rated to be safe for foods, but I'm not sure if nic liquid qualifies as a food :)
  17. Commie

    Looking for a mod

    I'm looking for a mod, please advise which one to get. Here's what I'm looking for: As short as possible. 2000+ mAh capacity, or ability to fit an 18650 into it At least 15W capable Don't care if it's a mech/regulated/VV/VW Preferably box style, sturdy to stand up Something that can run an...
  18. Commie

    Why a Reo?

    I've always been a fan of side-by-side mods. As in, battery is in parallel to your juice tank and atomizer. Made a few atrocious mods myself. Then I tried a VMod (mind you, that was before reomizers came out, so all that with cartos). I liked the VMod, but everyone was nudging me towards a...
  19. Commie

    Modding SL Reos?

    I just wondered -- have any of you tried to grind out additional squonk holes in the SL Reos? Something like symmetrical hole to the one in the door, to squeeze the bottle from two sides? Or one on the side of the Reo, to make it ambidextrously squonkable?
  20. Commie

    My Grand tumbled out of the car

    Well, it's a pre-jump picture. But I swear, it looks about same :)
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu