I just had an email from Cloudhouse (Nathan) - he's put my order on a courier (Colissiom) and said it should get here faster.
All being well, I should have it by Friday
Anyone here used fasttech.
- Thread starter trouble1000
- Start date
- th_trl_thread_readers 0
- Status
All being well, I should have it by Friday
Terry, going back to those Lemo plugs, the o-ring only has 1 plug on it, I've just got mine out the bag I put them in to have a look, and you get 2 with the Lemo.
Ooop`s My bad, i was tired and didn`t realize it was the nano size ! SOZ
Hope you like your prezzie george 
Hi Terry thanks again for the mail and the blue moo taster. I do normally stick to 50/50 mix and my nic level varies between 12 and 18 so I'm really enjoying it. I've bookmarked the supplier so I will probably put an order together after Christmas, I've got plenty to keep me going now.
Cheers bob, i thought it was a bit strange them having 4 nib`s on them,
You are most welcome dave, They are brilliant there, as you can tailor to your own preference. Since i have started with the variable mods, i now tend to go a bit heavier on the VG, and lower on the nic. But you can also add extra flavour to make up for the lack of PG ( Brilliant )
Vape mail for me today. My Lemo arrived, I ordered it from ali express on 26/11/14 so 10 days is pretty good from China.
Bob is right the coil it comes with is actually pretty good, this is the first atomiser where I've used the coil it came with, although I did heat it up and squeeze the wire together a little. Not so much that it's tight, there is still space between the wires but I thought a little would be good. Gave the whole thing a bit of a clean with soapy water and a toothbrush before as well as there were a few tiny bits of metal in the airflow control section.
Anyway wicked it with rayon and part filled it with Mom and Pops Krunchberry, set the airflow to fully open and am vaping away at 25W and it's really good. You really do get clouds comparable with an RDA because of the amount of air that can pass through it if you crank the wattage up. Not sure how it compares to an orchid like some of you guys are into.
It's pretty big, I've got it on the rDNA 40 and it's about as tall as the mod! I reckon the smaller "drop" would look better but I like the fact you get 5ml capacity, it drinks the juice at 25W quickly!
In short, buy one
Bob is right the coil it comes with is actually pretty good, this is the first atomiser where I've used the coil it came with, although I did heat it up and squeeze the wire together a little. Not so much that it's tight, there is still space between the wires but I thought a little would be good. Gave the whole thing a bit of a clean with soapy water and a toothbrush before as well as there were a few tiny bits of metal in the airflow control section.
Anyway wicked it with rayon and part filled it with Mom and Pops Krunchberry, set the airflow to fully open and am vaping away at 25W and it's really good. You really do get clouds comparable with an RDA because of the amount of air that can pass through it if you crank the wattage up. Not sure how it compares to an orchid like some of you guys are into.
It's pretty big, I've got it on the rDNA 40 and it's about as tall as the mod! I reckon the smaller "drop" would look better but I like the fact you get 5ml capacity, it drinks the juice at 25W quickly!
In short, buy one
Looking for nano kits i found a mini Bob.
Must be a clone of the Erlprinz(i haven't seen the genuine)
For £8 think i'll add one.Was in two minds as Ian said no good and Bob said good.
$13.61 Mini RTA Rebuildable Tank Atomizer (3.0ml) - acrylic + stainless steel / 20.5mm dia. at FastTech - Worldwide Free Shipping
Must be a clone of the Erlprinz(i haven't seen the genuine)
For £8 think i'll add one.Was in two minds as Ian said no good and Bob said good.
$13.61 Mini RTA Rebuildable Tank Atomizer (3.0ml) - acrylic + stainless steel / 20.5mm dia. at FastTech - Worldwide Free Shipping
I got my full size "Bob" from Focalecig and it was an A-Mod one, which are normally fairly reliable clones.
The Erlprinz is actually just the cheaper version made in China for the Original company, rather than in Austria to reduce the costs, to sell to those that cannot afford the Austrian made one.
That'll be me then.
Well, it's a lot of difference between £110 for the erlQueen & £37 for the erlPrince
Vince...Do you remember when we were talking about a single coil build in the orchid ?? Well i did one of mine earlier a standard coil @ 1.5 ohms, and it works brilliantly Splitting the wick ends, and feeding to all four juice channels, works just as well as a dual coil set up in my opinion. It`s the first time i have used 28 gauge wire, and i found it a lot easier to work with than 30 ! On to the Hana set @ 20 watts, and it is up there with the best.
Splitting the wick ends, and feeding to all four juice channels, works just as well as a dual coil set up in my opinion. It`s the first time i have used 28 gauge wire, and i found it a lot easier to work with than 30 ! On to the Hana set @ 20 watts, and it is up there with the best.
Vince...Do you remember when we were talking about a single coil build in the orchid ?? Well i did one of mine earlier a standard coil @ 1.5 ohms, and it works brilliantly
Great minds eh !!!
In other news I'm 99.9% certain I'll be getting the Ipv mini
I've spent ages going through different coil configurations
on the steam engine site and ohms calc and I shouldn't be
needing more than 30 watts
So hopefully, i will have both Hana`s before ian has got one
I found a song for Ian,just to cheer him up over the delay
https://www.youtube.com/watch?v=qgFL9wWDndc
Personally, i think 30 watts is plenty vinnie. I Haven`t even been that high on my Hana, i think 24.5 is the highest i`ve took it with a .8 coil, and it was getting too hot a vape, nice. but a bit hot for me
I don`t understand why these manufacturers are making them go as high as 250 mate, i mean come on now
So whare are you thinking of getting the mini from ?
Personally, i think 30 watts is plenty vinnie. I Haven`t even been that high on my Hana, i think 24.5 is the highest i`ve took it with a .8 coil, and it was getting too hot a vape, nice. but a bit hot for me
I don`t understand why these manufacturers are making them go as high as 250 mate, i mean come on now
So whare are you thinking of getting the mini from ?
I know what you mean, when a guy starts talking about coiling up with 22 awg
I find something else to read
There are any number of vendors getting the mini in, probably from the end
of next week, I'll look for a deal on a decent battery & charger thrown in
Well good luck mate, and i think you have made a great choice
Where abouts in the NW are you vinnie ?
Oi, I've got some 22awg and my KFL+ v2 that I have on the VS DNA40 has 0.45mm on it which ain't far off the mark, can't remember what I made my 0.26 ohm Doge with but that was pretty large wire and that gets vaped at anything up to 84w when the battery is fully charged, too hot for more than a couple of seconds vape though
- Status
Similar threads
- Locked
