BF Mods by Custom-Classic

[rudy4653]

I used Vapage bottles in my Pekos with no issues.
The only thing I would say is the stock bottle screw caps with o ring are better quality than Vapage cap with hole drilled in those white caps.

 

[TheKiwi]

Vapage bottles are nicer to squeeze, but all of mine starts leaking a little after 2-3 months of use.

On the flip side, I'm still using the same bottles that came in my reos 2 years ago. Go figure


Sent from my iPhone using Tapatalk

 

[Loopy1224]

Hopefully Loopy'll check in and give us an update... He's been usin' the vapage bottles for a while now....





Eta: Also,.... I believe my favorite lady penguin has also been using them.... I look forward to her opinion, as well.

I don't take my CC to work so I use the 6mm bottle during the week because it is plenty big enough to last the rest of the day. On the weekends I switch to the Vapeage bottle and haven't had any trouble at all. No leaks and still on the first one I started with and it is holding up just fine. Again the small neck can be a pain to fill especially with thick juices but that is a tiny problem that I don't mind dealing with. Why switch you may ask? Well I like to switch juices so if I only used the Vapeage bottle it would still be half full the following day.

 

[beckdg]

Vapage bottles are nicer to squeeze, but all of mine starts leaking a little after 2-3 months of use.

On the flip side, I'm still using the same bottles that came in my reos 2 years ago. Go figure


Sent from my iPhone using Tapatalk

Half the reason I only opted for regular bottle size.

I've gone through a couple bottles in my t-mod in a couple months. Not vapage, methinks, but softer style.

My REO bottles, I'm still on the first one in over a year.

Seepage sucks when you still have 4 hours to drive before you can stop.

The other half... The softer bottles tend to be softer on the hand, but not much different when creating hydraulic pressure to push juice up IME.

with that... and a larger air gap in a larger bottle with the same amount of juice in it, I don't experience the "easier to squonk" benefit others seem to notice.

Maybe it's the girly size meaty sausage hands I have. I dunno.

What i do know is I get a lot more dry hits with a lot more juice left in the bottle with the larger, softer bottles... and I have to refill them just as often, if not more because of it.

Again, just one idiots experience. Take it at face value.

Tapatyped

 

[pennysmalls]

I GOT Holes!

I'm jealous of your holes.

 

[beckdg]

I'm jealous of your holes.

WOAH penny!

I didn't know you cared.

[emoji14]

Tapatyped

 

[BobC]

I'm jealous of your holes.

WOAH penny!

I didn't know you cared.

[emoji14]

Tapatyped

One thing I notice about CC mod squonkers, they're a strange lot

 

[beckdg]

One thing I notice about CC mod squonkers, they're a strange lot

A bunch of bottom feeders I'd say.

Tapatyped

 

[Alexander Mundy]

One thing I notice about CC mod squonkers, they're a strange lot

 

[BobC]

Of course, I am a squonker, and soon to be a CC mod squonker

 

[majik cloud]

Anyone used the fat daddy bottles, the vapage ones are not available in the uk, just been on the vapage site and shipping to the uk is mad.

 

[custom-classic]

HEY, Majik! Yes, Subohmies, over in AUS has been using the FDV 10ml bottles for about a week or so. I'll go back and find his post....

 

[custom-classic]

It was back on page 117...

Juat a quick update on the fatdaddy bottle
Yes the bottke is tall but it fit flush on cc mod. Im happy with it

 

[majik cloud]

nice one cc, will have a look thanks, lovin it by the way.

 

[custom-classic]

Great to hear, my friend!

 

[Nautilusfan]

Quiet in here tonight. Figured we'd have some pics of Bobs and MM's progress

 

[custom-classic]

Sorry I haven't been around this evening.... I had a tooling debacle...
I use a chucking reamer to get to final diameter on the battery hole. As my reamer has slowly gotten a bit duller, more heat is introduced into the part, as it goes deeper... I've been searching for the perfect end mill to do the job, but finally realized that no one makes the exact one I need, in the specs I need it in...

I finally just decided to have one made,...well, 3 actually..... anyhow, I got 'em in today, and they all looked great! However,... I didn't notice that the one I grabbed to use on Bob's battery hole, had a burr, way up high on one of the flutes... Everything was going along great until I reached the burr....

This is what it left behind...

About a quarter on an inch of slightly rough finish, at the top of the battery hole... Needless to say,... I was not happy.

I contacted Bob to see if he wanted me to just start over on his mod, but he was really cool about it.
He said since it was just on the inside of the mod, he wasn't worried about it, and I shouldn't be worried about it either...

So, I just wanted to take a moment and tell ya'll, that Bob's a helluva guy.

I will, of course,... be knockin' some off the price, just to try and make myself feel a little better about it...

Anyway,... Once we got that all worked out,... I proceeded to try and get caught up to where I should be, by the end of today...

We should now be back on track...

 

[TheKiwi]

Next step: getting 2 Coreys cloned.


Sent from my iPhone using Tapatalk

 

[Nautilusfan]

Wow man. That's not good Sorry you've had those issues. I was afraid something had gone off track when you hadn't been around Great of Bob to be so understanding! He's a pretty good guy.....even with a slightly burred hole

 

[BlueSnake]

Sorry I haven't been around this evening.... I had a tooling debacle...
I use a chucking reamer to get to final diameter on the battery hole. As my reamer has slowly gotten a bit duller, more heat is introduced into the part, as it goes deeper... I've been searching for the perfect end mill to do the job, but finally realized that no one makes the exact one I need, in the specs I need it in...

I finally just decided to have one made,...well, 3 actually..... anyhow, I got 'em in today, and they all looked great! However,... I didn't notice that the one I grabbed to use on Bob's battery hole, had a burr, way up high on one of the flutes... Everything was going along great until I reached the burr....

This is what it left behind...

About a quarter on an inch of slightly rough finish, at the top of the battery hole... Needless to say,... I was not happy.

I contacted Bob to see if he wanted me to just start over on his mod, but he was really cool about it.
He said since it was just on the inside of the mod, he wasn't worried about it, and I shouldn't be worried about it either...

So, I just wanted to take a moment and tell ya'll, that Bob's a helluva guy.

I will, of course,... be knockin' some off the price, just to try and make myself feel a little better about it...

Anyway,... Once we got that all worked out,... I proceeded to try and get caught up to where I should be, by the end of today...

We should now be back on track...

I don't know for sure as I don't post much and mostly just lurk, but I'm guessing that this imperfection is something very noticeable to you but almost, if not imperceptible to the rest of us. JMHO.