Boba's bouny and carto?

Status
Not open for further replies.

bogeyjim

Ultra Member
ECF Veteran
Verified Member
Feb 3, 2010
1,235
372
Boulder, CO
Hey guys, just got my bobas bounty in today and love it!

Problem is i can only drip with it!

I put it in a fresh carto and it didnt go all the way down and i burned a brand new carto!!

Any ideas how to get this juice to vape out of a carto... oh, i did get two puffs in before burning the carto and i got tons of vapor but absolutely no flavor....

Im lost!
 

six

Vaping Master
ECF Veteran
Verified Member
Feb 17, 2011
3,706
4,504
under the blue sky
You didn't mention what type of carto, but I'll assume it's a filler carto like a boge or a smoke tech.

When you put 100% VG juice in a filler carto, you need to make sure the whole thing gets wet. I shake them like a thermometer. I'll put in half a dozen drops at a time and shake between each half dozen drops.

Others use the condom fill method or a syringe. Both are good ways to make sure a carto gets soaked.
 

studio52

Super Member
ECF Veteran
May 11, 2011
712
174
Meridian MS
You can also use some thin PG to wet the carto before adding your juice, I keep a bottle of 80/20 pg/vg on hand for just such need. Once the carto is fairly wet, add 8 to 10 drops of your juice and then more if it holds it, vape it for a while, not much flavor, but then as you add you juice your cart stays wet and the full flavor will appear shortly.
 

The_Jerkstore

Senior Member
ECF Veteran
Verified Member
Syringe is best IMO. They're very cheap. Your local drug store might have some. Just make sure you get a 20 gauge needle or bigger. By bigger, that would be a smaller number like 18 gauge. If not, lots of vendors sell them. I've been rockin Gorilla juice in a 510 carto all week without issue.
 

boneshark187

Senior Member
ECF Veteran
Verified Member
May 4, 2011
188
143
New Jersey
I only drip my Bobas. The flavor is meh in a carto for me.

same for me...I'm dripping 6mg boba's on a 1.5 lr joye atty on a 3.7v device.

I tried using boba's in 2.0 ohm boges cartos & found the same, the taste was not there & you gotta make sure that it's filled from the bottom or with a syringe not to get a dry hit. Although i've seen some video reviews by pbusardo where he's using a jtank and a slotted boge carto without a problem using boba's.

Not sure - that may be the trick for boba's to use a big ol' tank with a boge carto and having the slot towards the bottom really keeps the carto wet.
 

Jim Bob

Ultra Member
ECF Veteran
Dec 21, 2011
1,266
537
Kentucky
Until you get a syringe try adding drops, thermometer shake...... waiting, add more shake wait, add more ; once you are sure you have at least 1 ml in let sit for an hour ( I know) add some more drops, shake then test it, also unless you dilute you will likely need to wait a bit between vapes as it will wick much slower also I would fill one this way to sit overnight for the next day adding more in the am before trying.. Sorry you ruined a good carto
 

Fernand

Super Member
ECF Veteran
Oct 5, 2010
907
747
Californeea
Wow! I've never tried an all VG juice. Do you like the juice a lot? I've been wanting to try it but it sounds like a hassle.

No hassle, and no chemical taste. No PG acid stomach. No sleepy feeling. Better vapor. What a difference! :2c:

Personally I like Humco (= Rite Aid = CVS) USP Glycerin with 5% flavoring and the appropriate amount of Nicotine in VG. It's thicker than the PG liquids, but where it matters, a few drops of water bring it to the same viscosity as PG. Simple, cheap and clean.

BogeyJim, CE2 is a top horizontal coil carto with long wicks dipping down into the juice. They're a little finicky but can be very nice and cannot be burned. They come in metal and clear plastic barrels ("Clearomizer"), and different sizes. OK with any juice.

Clearomizer1.jpg
 
Last edited:

madsen6466

Senior Member
ECF Veteran
Verified Member
Dec 8, 2011
216
108
tennessee
I'm so glad this thread was already made. I've been sitting on a couple oz's of boba's letting it steep, waiting to give it a shot and was just about to try to fill a boge 2.0 when I remembered this thread. Just used the needle method... gonna let it soak through and see how that works...

also - anyone have a source for these ce2's?
 
Status
Not open for further replies.

Users who are viewing this thread