bulk attys
- Thread starter Tnscooter
- Start date
- th_trl_thread_readers 0
-
- Tags
- madvapes vaporkings
- Status
I'll be in town tomorrow and can put a meter on them. I really should list that spec on the product page.
Hey Prole,
Sorry I didn't make it in there today but I'll definitely be there in the morning.
Sorry I didn't make it in there today but I'll definitely be there in the morning.
No worries, less have a run of bad luck current attys should be good for a spell, good pricing on these, have not shopped with you before, and if the ohms look good will give these a go better pricing than my current atty source
Sorry guys, Rob gave me the ohms yesterday to post and I got busy.
The 510's are running around 2.3 but could have a normal variance and the 901's are running 2.9 to 3.1.
Thanks
The 510's are running around 2.3 but could have a normal variance and the 901's are running 2.9 to 3.1.
Thanks
We expect to see +/- .2 Ohm variances. We just state this because there are some people that will meter an atomizer and if it's a 3 Ohm atomizer and it reads 3.1 Ohms, they get a little excited about it.
Thought I'd piggy back here instead of creating a whole new thread.
Do you have any plan's of getting the standard Joye 306's in bulk atty packs?
Do you have any plan's of getting the standard Joye 306's in bulk atty packs?
I'd have to do some checking to see how popular the regular 306's are. I've been ordering 10,000 atomizers at a time for the bulk packs and if the regular 306 didn't sell well, or quick enough, that would be a lot of cash tied up in atomizers.
I'll check around though!
I'll check around though!
Wow that's alot of atty's! lol
Would be cool if you could do in bulk but if not feasible , single atty's would be ok also if you can.
Would be cool if you could do in bulk but if not feasible , single atty's would be ok also if you can.
Just curious if anyone else has experienced or if VK has had any reports of it. Is not so much a taste but rather irritation in the throat, that is persistent.
I have only tested two out of my 901 Bulk Pack.... it occurs whether on my madvapes box mod 3.7v (14500), my dse-905, or 808 5v pt, waited till I finalized my variable regulated Tenergy Universal DC-DC Converter and Voltage Stablizer--Any Voltage Control setup for my pass throughs before saying anything in the hopes of finding a sweet spot that remedied the issue and making these partially viable but unless setting below 3v under load which is not much of vape the taste/irritation is consistent and just increases over 3-5v underload.
needless to say are unusable off the 5v 2 amp ac/usb adapter.
Who makes these? I don't have the issue with the SLB 901s from another supplier, I have used/cleaned the 2 out of the bulk pack I have tried enough to clear out any possible juice perhaps put there during manufacture to prevent oxidation so do not think that is it.
Solutions/suggestions will me most welcome. Wondering if maybe a replay of the mesh issues on some 510's read about here a few months back.
I have only tested two out of my 901 Bulk Pack.... it occurs whether on my madvapes box mod 3.7v (14500), my dse-905, or 808 5v pt, waited till I finalized my variable regulated Tenergy Universal DC-DC Converter and Voltage Stablizer--Any Voltage Control setup for my pass throughs before saying anything in the hopes of finding a sweet spot that remedied the issue and making these partially viable but unless setting below 3v under load which is not much of vape the taste/irritation is consistent and just increases over 3-5v underload.
needless to say are unusable off the 5v 2 amp ac/usb adapter.
Who makes these? I don't have the issue with the SLB 901s from another supplier, I have used/cleaned the 2 out of the bulk pack I have tried enough to clear out any possible juice perhaps put there during manufacture to prevent oxidation so do not think that is it.
Solutions/suggestions will me most welcome. Wondering if maybe a replay of the mesh issues on some 510's read about here a few months back.
Last edited:
Hi Prole,
Sorry you are having a problem with the 901's. I've not had any reports like this about any of the atomizers. The 901's come direct from SLB and the only thing different about them is I buy them in high quantities and print bulk on them for warranty identification.
If you'd like to send some back to me to check out I'd be happy to.
Thanks
Rob
Sorry you are having a problem with the 901's. I've not had any reports like this about any of the atomizers. The 901's come direct from SLB and the only thing different about them is I buy them in high quantities and print bulk on them for warranty identification.
If you'd like to send some back to me to check out I'd be happy to.
Thanks
Rob
Rob, stalk the wee hours I see.......will do, will take a couple days before can make to the PO. Will PM you, or PM me with where/what to send, stuff you may want me to check, try before I can get them in the post. Can send a small sample of the juice as well if that might be of help. Only opened two out of the ten thus far, and from the same five pack box.
I never really had a problem with DOA or couple hour attys so since they are sealed individually did not see a need to open 'em all to test for doa.
Thanks for the quick response.
I never really had a problem with DOA or couple hour attys so since they are sealed individually did not see a need to open 'em all to test for doa.
Thanks for the quick response.
The regular joye 510 bulks are around 2.3 ohms. I am very happy with them so far..If you're on the fence go for it! Good stuff Rob! Will probably be ordering some more of these soon. As an aside i wouldn't mind seeing some HV bulk Joye 510's too. Say around 3.5 ohms.
Man, seems like the bulk packs are working out for everyone but me so far, what a bummer.... the two 901's I opened from my 10 pack both had a foul taste, and I noted when dry burning the 1st one, in attempt to make usable tendrils of black smoke mixed in with the vapor, waiting to hear back for a hopeful resolution/solution as hoped had found a new primary atomizer supplier
On the way, great customer service btw!!!!!!!!!! curious to see what you find on your end, the two I opened and tried...may of been the only ones out of the 10 so afflicted. had the same issue with a pair of 510 attys I procured from another supplier during the time there was that "bad" "inferior" ni-chrome mesh issue going on... the taste is very similar to that.
I really appreciate you taking the time and trouble to look into..... would recommend you guys on the basis of your customer service alone
I really appreciate you taking the time and trouble to look into..... would recommend you guys on the basis of your customer service alone
- Status
Similar threads
- Locked
