I understand the Cannon line is an 801. What differences would I notice in use, compared to the 510s?
Cannon/Stealth VS IKV LR 510 1.8Ω Atomizer. Whats the difference?
- Thread starter acv987
- Start date
- th_trl_thread_readers 0
- Status
Cooler vape, better flavour, VP about the same, TH better with 510. The Canons are close to 801s, but are not.
I don't have an Iken 510, so maybe these are the same, but the cannons are physically bigger in diameter than a 510 as well that tapers a bit at the end but is still too large to accomodate a 510 drip tip. No leaking on the one I got last week, it's a 2.5 ohm.
REO ftw
how are the cannons working on your reo? every time I try and use them on mine I get frustrated, give up, and go back to my cisco 306's because it leaks enough to fill up the catch cup and start flowing down the side when I pick it up, I also notice that when I try and "blind squonk" I don't feel the pressure change that normally signals me to stop inhaling/squeezing the bottle. love the flavor though and now I need to try out an 801 with an adapter.
Use my O-Ring trick and you wont have any issues with leaking over the catch cup, plus it will Auto feed the Cannon Atty with the O-Ring on the cannon/Reo set up ! #83 Danco for the cannon,,,, #78 for 510 & 306 with reg 306 drip tip 83 with cannon drip tip
They are built to run how they run, any 801 internal on any Atty with a 510 thread with the holes in the threads will have some liquid come back out through the bottom end, especially with as much fuel as the cannon takes to run, and with a bottom feeder with a catch cup and using the O-Ring system trick I made up you have NO LEAKAGE any longer plus it turns the Reo's into an Auto feed system for the most part, just trying to help here, you may like these very much if you try one, these are the only Attys I run on my Grands and love them, they give more flavor than any other Atty on a Reo grand too or any bottom feeder with a catch cup in my opinion.
I bought 2 801 Cannons. Used one and it leaks quite a bit.. I drip 2-3 drops, and 75% of the liquids ends in the catch cup. Been vaping for 20 months now, and this is the first atomizer I use that does not hold more than 3 drops of liquid. Even the tiny 306 holds 3-4 drops.. I will try and find the o ring thread and give it another shot.. otherwise it was a $20 mistake...
I think Iken has a whole thread on leaky 801s, and there are plenty of people having this issue..
Could you please elaborate on your o-ring trick. I have 2 of these cannons that leak on both my Mini and Grand and would love to get them working. Thanks.
Nevermind. I located your post on the subject. Thanks for the tip for bottom feeders.
Thank you so much!! I remembered seeing something about o-rings helping with the leaking issues but I couldn't seem to find it anywhere on the reo or ikenvape forums, I'll be heading to home depot tonight to try this out.
I have to attest to mwa's awesome O ring fix. With the cannon and my REOs it is pure bliss. I heard about the leaking, so only ordered 5 to share with my better half as a trial. I loved them so much, I have 15 more coming tomorrow. The O ring is such an inexpensive and perfect fix. btw, I have been using the 2.0 stealth cannon.
Isaac, the cannons rock my vaping world. Such a nice, smooth, flavorful atty. Thank you!
Isaac, the cannons rock my vaping world. Such a nice, smooth, flavorful atty. Thank you!
Using O-rings on you Reo's !
I happen to stumble upon this trick today just trying to find a way for the juice in the catch cup not to spill out any longer and while doing this also found it makes the Reo's self feed as well as giving you the ability to adjust your draw by how tight or lose you apply your O-Ring over the catch cup, push it down further = tighter draw, loser = lighter draw ! The O-Rings I am using are posted below and all available at Home Depot
Reo Min = Danco #78 = w/510/306 ,, Danco #83 W/801 or Cannon
Reo Grand = Danco # 83 with Cannon/801 ,,,#78 w/510/306
Reo Woodvill = Dnaco # 78 = w/801
OK so using these with the Iken Cannon Atty's : Here is what this does, slip the Danco O-Ring over your Atty down the tube until it sits on the top of the catch cup. The more you push down into the catch cup the tighter the draw and vice verse for a lighter draw. You will find 2 things that now happen while using the Danco O-Rings 1st your Reo will no longer spill any juice out of the catch cup which is a nice plus for when your carrying it around or want to set it down on your cars passenger seat like I often do. 2nd these O-Rings pretty much make your Reo's into a self feed system now with the O-Ring on your Reo it creates a vacuum affect an when you take a pull it will now self feed your Reo, once in a while you may have to squank the bottle but overall I'm finding they now self feed with the O-Ring which is super. This will also work for those who use 801 Attys. It will also work with 510/306 Atty's by using the # 78 O-Ring with 510/306
This really works super anyone using a Reo I suggest you try using these O-Rings over your Attys down onto the catch cup it's an overall win win situation
This really does work! The mini woodvil catch cup may need a fatter ring in the same size for the 306 drip tip. The 801 works very nicely in the mini woodvil though. Favorite is the 801 in the reg Woodvil, love how it sits right on top of the catch cup!! Thank you!
Last edited:
- Status
Similar threads
- Locked
