Cappy's gg avs 510 part2
- Thread starter cappy
- Start date
- th_trl_thread_readers 0
- Status
Thanks Cappy, will give it a try tomorrow. Tried an adapter by itself and although first tank was good..then flooding hit me 
. With the off centre atty it may be the connector. Have a look at this picture and see if your connector looks similar:
http://i808.photobucket.com/albums/zz9/HoPeFuLLL/Troubleshooting/P1010689.jpg
Notice the wall is not even, I replace that one for a client.
. With the off centre atty it may be the connector. Have a look at this picture and see if your connector looks similar:http://i808.photobucket.com/albums/zz9/HoPeFuLLL/Troubleshooting/P1010689.jpg
Notice the wall is not even, I replace that one for a client.
Watched again. One thing maybe worth doing (to maximize tank use) is putting the hole at the 901 side of the adapter or for people who exclusively want 510 actually putting the adapter on and drilling the hole through the very bottom, atty connector and all. Would save slotting it then. What ya think Cappy?
Does it need to have flow through the tiny hole in the threading bottom side of the 510? Is this why your hole on the top?
And make sure your 510 is ok, tried a couple then and 1 wont screw to the bottom of the adapter. I suspect it was this bad threading that made my earlier attempts inconsistent.
Does it need to have flow through the tiny hole in the threading bottom side of the 510? Is this why your hole on the top?
And make sure your 510 is ok, tried a couple then and 1 wont screw to the bottom of the adapter. I suspect it was this bad threading that made my earlier attempts inconsistent.
Last edited:
Cappy,
I have replacement connectors to fix that crooked connector. I missed your call today but give me a buzz tomorrow.
I have replacement connectors to fix that crooked connector. I missed your call today but give me a buzz tomorrow.
Tank is very close to empty this way. Slotting is important I think it will flood with hole on 901 side anyway.
I think the best way to make the 510 connector would be like I said long ago and it is to make an all brass or aluminum connector with a native 510 connection like the adapter looks like on the top of the connector, then have one or two laser holes at the bottom of the side walls, this would slow the liquid down enough that the 510 wouldn't flood and allow just the right amount in, it could be tested by starting off with one laser hole, then move to two and so on to see what works best. I have been testing with adapter and connectors for months now and this seem to work best, Rob since you have been the longest and best GG supplier I would like to here your opinion if that's possible or Cappy's
Cappy I think the video is great and very helpful to a lot of people keep them coming the adapter is a good way, but I still think a stock native 510 all in one piece connector would be best for this and wished Imeo would make them up for everyone to use and I hope he does
OK I have done so twice Cappy, if you PM him to use MWA's idea for the connector with your crosscuts on the bottom maybe we can get this once and for all
Edited post can be read by all moderators and will, great job Cappy video is very informative to all
Gave this a go via your instructions. Put the hole down the bottom though and it happened to cut a channel in the AVS atty connector top. Unfortunately my hole was a bit too big and I had flooding. So I changed the AVS .... plug to a new one and tried again.
No flooding and a nice tight draw like I like. Fluid must be getting through threads and my wonky filing. Might try my tiny tiny drill bits to ease the draw slightly but I'm coming to the conclusion that a mass produced more exact adapter would be the go, probably the whole .... plug area in a 510 format with a hole near the bottom of tank (clearing o-ring).
No flooding and a nice tight draw like I like. Fluid must be getting through threads and my wonky filing. Might try my tiny tiny drill bits to ease the draw slightly but I'm coming to the conclusion that a mass produced more exact adapter would be the go, probably the whole .... plug area in a 510 format with a hole near the bottom of tank (clearing o-ring).
I will make a sample the day after tomorow so I can test it mwa so no reason to send me 3 times in a row pms cappy hahaha
Last edited:
Imeo.....
You are feeling very relaxed...
In another place beyond Earth...
510 connector Imeo...
You must make a 510 connector. It is your duty and purpose in life. Seek only to make a 510 connector Imeo.
When I snap my fingers three times you will arise from your chair and go to the machines.
1-2-3
You are feeling very relaxed...
In another place beyond Earth...
510 connector Imeo...
You must make a 510 connector. It is your duty and purpose in life. Seek only to make a 510 connector Imeo.
When I snap my fingers three times you will arise from your chair and go to the machines.
1-2-3
My 510 atomizer works more than nice inside AVS. I just put the adapter and the atomizer without any modification. That means that I will make a 510 adapter for AVS just like the 901 but with 510 threads. I dont think we need something else. Anyone who disagrees?
Rob, I am not relaxed, I am at home and I work like hell to make the GGTB and all the other stuff to send to all my sellers.!!
May need a tiny feeder hole in the thread Imeo, otherwise can't see why not fine. Oh actually, will need to be raised like the adapter or MP o-ring wont attach, 510 are short.
Last edited:
My thoughts are to make it 1 mm longer so it will raise 1mm from the existing 901 one and nothing else. Agree Hope? I dont see a reason for a side hole. Mine works exellent without any modification. Why did you modified yours or why other people like storly mwa or cappy make holes?
Seems like it's how it fits together, if edges not flush, in comes some juice. But if everything perfect will be no juice coming in hence need for hole in adapter for juice.
- Status
