Has anyone tried a Kanger Protank II on the Cloupor? What kind of success have you had?
Cloupor 30 watt box mod
- Thread starter acc1977
- Start date
- th_trl_thread_readers 0
- Status
I had it set to 7 watts and it wouldn't fire it. Now the tank won't fire on anything. I have used the tank on 9 watt setting on my MVP 2.0 and it worked fine. The coil head was just replaced less than a week ago too. The tank does have standard 510 threading doesn't it?
I have the dna 30 myself, I've never tried to run a pro tank on her. I use my RDAS mostly kayfun and taifun. I would tend to agree that the power (wattage) unless you went very low will distort the coil. What you CAN do is rebuild the pro tank coil yourself, when you rewick, use cotton. You should be able to vape at a higher wattage with your rebuilt coil. They are very easily rebuilt. If you have never done it, they have a step by step tutorial on you tube that will walk you through the entire process. You will need kanthal wire, I use 28 gauge. Cotton for wicking. Basically you will pull the bottom pin out, then the rubber insulator , then you can remove the old coil. Rewind a new coil, the video will show you exactly how to do this. Rewick with cotton. Slide the insulation back on one leg of the wire only and back into casing.position wick and coil replace pin and clip the wire leads. Then put the rest of the coils housing back together. If cotton is too long cut to fit. Then you should be able to run that coil without problems. But watch the video it goes step by step. Hope this helps you. Best wishes
Last edited:
Your welcome! I've rebuilt them myself and you can really get those coils rocking! Check out the you tube tutorial. It's pretty easy. Gives pretty good results too! Lots more vapor too! 
Your welcome! I've rebuilt them myself and you can really get those coils rocking! Check out the you tube tutorial. It's pretty easy. Gives pretty good results too! Lots more vapor too!
I watched Rip Trippers video and I will definately be giving that a shot.
It could have burned the small rubber insulator in the coil head causing it to short. Try a new coil, or take that one apart and inspect it and rebuild.
Sent from my iPhone using Tapatalk
I dont use protanks, but I do run my Aerotank Mega on my Cana everyday. The coil is 2.0ohm. It runs like a champ at 25-30watts. Yes, its most definitely burning the coil and wick faster. But I dont mind much cause its just my sweet flavor tank. I use my rda's for my tobacco juices.
It would work no prob, at minimum wattage, but you would never use 20 let alone 30 watts with a pt.
That said, it would still fire the pt, and give you a solid mod to grow with, and running a pt would probably get good batt run time since you'd be running it so low.
The Cloupor mod is one of the best bargains out, and has proven to be a solid mod.
Vape long aacquire Prosper.!!!
That said, it would still fire the pt, and give you a solid mod to grow with, and running a pt would probably get good batt run time since you'd be running it so low.
The Cloupor mod is one of the best bargains out, and has proven to be a solid mod.
Vape long a
Thanks for the advice
Let me know if that helps you
Sent from my iPhone using Tapatalk
I have used protanks and puritanks on my Cloupor DNA30 with no problem. The tanks were using 2.5 ohm standard kanger atomizer heads. I fully expected burnt vapes since I seldom exceed 6 watts on my Vamos. The only modification to the protank/puritank was the addition of the aerobase.
Last edited:
So, since I had a standard base protank 2 sitting around. I thought I would give it a try as well. Worked fine at lowest setting. Worked fine at 8 watts too, but I would just run it at 7 watts. 2.5 ohm on the atomizer I put in read at 2.7 on the Cloupor. Now, time to go back to my Kayfun.
- Status
Similar threads
