Confused out of my freakin mind

[Dusif]

I need some help from the vaping gods so please listen up and hear my prayer

Ive been having some problems, i recently got a galileo clone from FT... The thing broke and wouldnt fire anything... Now i got it working again... Or did i... It can fire a ce4 with no problem... But with my drippers it can only heat up the coils to a gentle warm to the touch temperature... Now what the H is going on here? :S... Ive rebuild the coils several times, tried diffrent builds and of course checked the ohms... Everything is as it should be but they wont glow


Sent from my iPhone using Tapatalk

 

[Dusif]

And the drippers work fine on the ego :S


Sent from my iPhone using Tapatalk

 

[Stosh]

Have you checked your batteries with a multimeter? Are they taking a full charge?

What ohms are your built coils? Sub-ohm coils can over-stress a battery, or over discharge it, either can be dangerous.
What make and model are your batteries? Are they high drain IMR?

 

[glycerol]

Faulty batteries? Try coils above 1.5 ohm.

 

[tj99959]

Sounds like it's post pulling time.

It's not uncommon for one head to push the positive post down a little so that other heads only make poor or no contact.

 

[Cr0tchF4i]

I have to adjust the positive contact on my drippers when switching between mech's- try unscrewing the positive screw under the rda see if that helps.

 

[Dusif]

The batteries are brand new freshly charged sony us18650vtc3 batteries, they take a charge
The coils are a 2,8 ce4, a 0,6ohm silica wicked and a 1.0 cotton bedded nano coil


Sent from my iPhone using Tapatalk

 

[Dusif]

I have to adjust the positive contact on my drippers when switching between mech's- try unscrewing the positive screw under the rda see if that helps.

They have solid pins and worked fine on the very same mech a few days ago

Nothing is wrong but for some reason it wont work and i really cant see why


Sent from my iPhone using Tapatalk

 

[Stosh]

Those should be top notch batteries, the weird thing being they fire a 2.8 ohm coil fine.
If your atty connections are clean, making good contact and the switch contact are clean, then it would seem the batteries can't produce the amperage you're asking of them. An in-line voltage meter would be great to see what the voltage drops are, but I'm guessing you don't have one, hence the questions...

From what you describe it would seem to be bad contacts, or weak batteries (possibly counterfeit ??)

 

[glycerol]

Perhaps it's the post. Also, do you use any lubricants on the threads?

 

[Stosh]

Just a thought, but if you built a 2.5 - 2.8 ohm coil on your dripper and it fires fine, then it would point at the batteries not producing enough amperage. The experiment would narrow down the possibilities...

 

[Dusif]

The batteries worked fine 2 days ago as well... Then all of a sudden the coil wouldnt fire as it wont now... If you hadnt guessed it im going nuts and craving nicotine... But i WONT light an analog ive been vaping for to damn long to go that way, id rather vape on the ego (that can fire my coils fine)


Sent from my iPhone using Tapatalk

 

[tj99959]

Still thing you have pushed the post down in your G clone. It only takes about 0.01mm to make the difference between a good contact and a bad contact.

 

[Dusif]

Tried with a panasonic cgr18650ch battery... No difference at all


Sent from my iPhone using Tapatalk

 

[Dusif]

Still thing you have pushed the post down in your G clone. It only takes about 0.01mm to make the difference between a good contact and a bad contact.

The post cannot come further up... And it does make contact i can get vape just not alot


Sent from my iPhone using Tapatalk

 

[Cr0tchF4i]

They have solid pins and worked fine on the very same mech a few days ago

Nothing is wrong but for some reason it wont work and i really cant see why


Sent from my iPhone using Tapatalk

Did one of the coils pop without you noticing? Have you tried poking them around a little to see? If you used a freshly charged battery it may have been a little much.

 

[glycerol]

Did you lube the threads or other parts recently?

 

[Wow1420]

Is any part of the mod, like the switch, getting warm or hot when you try to use it?

 

[Dusif]

Did one of the coils pop without you noticing? Have you tried poking them around a little to see? If you used a freshly charged battery it may have been a little much.

Its single coil builds and they fire fine on the ego battery


Sent from my iPhone using Tapatalk

 

[Dusif]

Did you lube the threads or other parts recently?

No change to the mod other than the above mentioned... Remember it will fire the Ce4 just fine


Sent from my iPhone using Tapatalk